GE D60 Instruction Manual page 156

5.4 FLEXLOGIC™
Table 5–6: D60 FLEXLOGIC™ OPERANDS (Sheet 7 of 8)
OPERAND TYPE OPERAND SYNTAX
INPUTS/OUTPUTS: Cont Ip 1
Contact Inputs Cont Ip 2
Cont Ip 1
Cont Ip 2
INPUTS/OUTPUTS: Cont Op 1
Contact Outputs, Cont Op 2
Current
(from detector on
Cont Op 1
Form-A output only)
Cont Op 2
INPUTS/OUTPUTS: Cont Op 1
Contact Outputs, Cont Op 2
Voltage
(from detector on
Cont Op 1
Form-A output only)
Cont Op 2
INPUTS/OUTPUTS DIRECT INPUT 1 On
Direct Inputs
DIRECT INPUT 32 On
INPUTS/OUTPUTS: REMOTE INPUT 1 On
Remote Inputs
REMOTE INPUT 32 On
INPUTS/OUTPUTS: Virt Ip 1
Virtual Inputs
Virt Ip 64
5
INPUTS/OUTPUTS: Virt Op 1
Virtual Outputs
Virt Op 96
LED TEST LED TEST IN PROGRESS
REMOTE DEVICES REMOTE DEVICE 1 On
REMOTE DEVICE 16 On
REMOTE DEVICE 1 Off
REMOTE DEVICE 16 Off
RESETTING RESET OP
RESET OP (COMMS)
RESET OP (OPERAND)
RESET OP (PUSHBUTTON)
SELF- ANY MAJOR ERROR
DIAGNOSTICS ANY MINOR ERROR
ANY SELF-TEST
BATTERY FAIL
DIRECT DEVICE OFF
DIRECT RING BREAK
DSP ERROR
EEPROM DATA ERROR
EQUIPMENT MISMATCH
FLEXLOGIC ERR TOKEN
IRIG-B FAILURE
LATCHING OUT ERROR
LOW ON MEMORY
NO DSP INTERRUPTS
PRI ETHERNET FAIL
PROGRAM MEMORY
PROTOTYPE FIRMWARE
REMOTE DEVICE OFF
SEC ETHERNET FAIL
SNTP FAILURE
SYSTEM EXCEPTION
UNIT NOT CALIBRATED
UNIT NOT PROGRAMMED
WATCHDOG ERROR
UNAUTHORIZED UNAUTHORIZED ACCESS
ACCESS ALARM
5-66
OPERAND DESCRIPTION
On (will not appear unless ordered)
On (will not appear unless ordered)
↓
Off (will not appear unless ordered)
Off (will not appear unless ordered)
↓
IOn (will not appear unless ordered)
IOn (will not appear unless ordered)
↓
IOff (will not appear unless ordered)
IOff (will not appear unless ordered)
↓
VOn (will not appear unless ordered)
VOn (will not appear unless ordered)
↓
VOff (will not appear unless ordered)
VOff (will not appear unless ordered)
↓
Flag is set, logic=1
↓
Flag is set, logic=1
Flag is set, logic=1
↓
Flag is set, logic=1
On Flag is set, logic=1
↓
On Flag is set, logic=1
On Flag is set, logic=1
↓
On Flag is set, logic=1
An LED test has been initiated and has not finished.
Flag is set, logic=1
↓
Flag is set, logic=1
Flag is set, logic=1
↓
Flag is set, logic=1
Reset command is operated (set by all 3 operands below)
Communications source of the reset command
Operand (assigned in the
of the reset command
Reset key (pushbutton) source of the reset command
Any of the major self-test errors generated (major error)
Any of the minor self-test errors generated (minor error)
Any self-test errors generated (generic, any error)
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
See description in Chapter 7: Commands and Targets.
Asserted when a password entry fails while accessing a password-protected
level of the relay.
D60 Line Distance Relay
↓
↓
↓
↓
↓
↓
↓
↓
↓
↓
↓
↓
INPUTS/OUTPUTS
5 SETTINGS
RESETTING menu) source
GE Multilin