Safety; Safe Operating Practices - Toro 02750 Operator's Manual

Safety

This machine has been designed in accordance with EN
ISO 5395:2013.
Improperly using or maintaining the machine can result
in injury. To reduce the potential for injury, comply with
these safety instructions and always pay attention to the
safety alert symbol, which means Caution, Warning, or
Danger—personal safety instruction. Failure to comply
with the instruction may result in personal injury or
death.

Safe Operating Practices

Training
•
Read the Operator's Manual and other training material
carefully. Be familiar with the controls, safety signs, and
the proper use of the equipment.
•
Never allow children or people unfamiliar with these
instructions to use or service the machine. Local
regulations may restrict the age of the operator.
•
Never mow while people, especially children, or pets are
nearby.
•
Do not carry passengers.
•
All drivers and mechanics should seek and obtain
professional and practical instruction. The owner is
responsible for training the users. Such instruction should
emphasize:
– the need for care and concentration when working
with ride-on machines;
– control of a ride-on machine sliding on a slope will
not be regained by the application of the brake. The
main reasons for loss of control are:
◊ insufficient wheel grip;
◊ being driven too fast;
◊ inadequate braking;
◊ the type of machine is unsuitable for its task;
◊ lack of awareness of the effect of ground
conditions, especially slopes;
•
The owner/user can prevent and is responsible for
accidents or injuries occurring to people and damage to
property.
Preparation
•
While mowing, always wear substantial, slip-resistant
footwear, long trousers, hard hat, safety glasses, and
hearing protection. Long hair, loose clothing, or jewelry
may get tangled in moving parts. Do not operate the
equipment when barefoot or wearing open sandals.
•
Thoroughly inspect the area where the equipment is to
be used and remove all objects which may be thrown by
the machine.
•
Replace damaged or worn silencers/mufflers.
•
Only use accessories and attachments approved by the
manufacturer.
•
Before using, always visually inspect to see that the blades,
blade bolts and cutter assembly are not worn or damaged.
Replace worn or damaged blades and bolts in sets to
preserve balance.
•
On multi-bladed machines, take care as rotating one blade
can cause other blades to rotate.
•
Check that the operator's presence controls, safety
switches and shields are attached and functioning
properly. Do not operate unless they are functioning
properly.
Operation
•
Do not operate the engine in a confined space where
dangerous carbon monoxide fumes can collect.
•
Mow only in daylight or in good artificial light.
•
Before attempting to start the engine, engage the parking
brake, disengage the cutting unit drive system and ensure
that the forward/reverse speed controls are in the
N position.
EUTRAL
•
Do not use on a slope of more than 16 degrees. Care
should be taken when using the machine on any slope
where ground conditions are such that there may be a
risk of the machine rolling over. The requirements of
Directive 2009/104/EC, 'Use of Work Equipment by
Workers at Work,' should be considered.
•
Remember that there is no such thing as a safe slope.
Travel on grass slopes requires particular care. To guard
against overturning:
– Do not stop or start suddenly when going up or
downhill.
– Machine speeds should be kept low on slopes and
during tight turns.
– Stay alert for humps and hollows and other hidden
hazards.
– Do not turn sharply.
– Use care when reversing.
•
Stay alert for holes in the terrain and other hidden hazards.
•
Watch out for traffic when crossing or near roadways.
•
Stop the blades rotating before crossing surfaces other
than grass.
•
When using any attachments, never direct discharge of
material toward bystanders nor allow anyone near the
machine while in operation.
•
Do not tamper with or disable the safety systems.
•
Never operate the machine with damaged guards, shields,
or without safety protective devices in place. Be sure
that all interlocks are attached, adjusted properly, and
functioning properly.
4