Fax Soft Switch; Fax Soft Switch Setting Change Quick Reference Table - Sharp AL-2020 Service Manual

[12] FAX SOFT SWITCH

1. FAX soft switch setting change quick reference table

Large item Middle item
Dialing Remote machine call
disable
Signal detection
Redial In case of an error
In case of an error
When busy
When busy
Arrival (Call-in) When CI detection
disable
External Setting of an external
telephone telephone connected
Remote switch
number
Remote switch
setting
Communication General
SG3
Transmission G3/SG3
SG3
G3
Reception G3/SG3
SG3
G3
Reception print Paper selection
Index
Switch content Key operator
Pause time None
Dial call signal User program SW 48-1, 2
DTMF-related item None
None
None
Pulse (10PPS) None
Busy tone detection None
Busy tone detection None
Dial tone detection None
Resend interval User program SW 4-1 – 4
Number of times of resend User program SW 40-1 – 8
Resend interval User program SW 4-5 – 8
Number of times of resend User program SW 41-1 – 8
CI detection None
CI signal OFF detection None
time
Yes/No None
Entry of a 2-digit number User program SW 2-5 – 8
Yes/No User program SW 8-5
Send level None
JBIG mode None
V34 mode function setup None
V34 symbol rate None
DIS reception check None
Line equalizer None
V34 send speed None
Manual send V34 None
Modem send speed None
RTN reception error None
CSI transmission None
Maximum reception length None
V34 reception speed None
Countermeasure against None
echo in reception
Modem speed in reception None
EYE-Q check only None
Automatic reduction print User program SW 24-8
Index print setup User program SW 32-6
AL-2020/2035/2040/2050/2060 FAX SOFT SWITCH 12 - 1
Soft SW No.
SW 5-5 – 8 When dialing disable/when error dialing
When dialing disable
SW 51-1 – 5 When dialing disable in PBX (private branch
exchange/Fax service, etc.)
SW 53-5 – 8 When dialing disable in PBX (private branch
exchange/Fax service, etc.)
SW 39-4 – 8 When dialing disable in PBX (private branch
exchange/Fax service, etc.)
SW 67-1 – 4 When pulse dialing disable
SW 7-3 When busy tone detection disable
SW 51-7, 8 When busy tone error is detected
SW 7-2
When send errors occur frequently
(For the New Zealand models, tough it is set
to 0, recall is performed in an interval of
1min.)
Whey busy occurs frequently
SW 12-6, 7 No call-in
SW 55-1 – 7 No call-in
SW 47-2 When an external telephone is connected
When remote switch is erroneously
detected
When remote switch is erroneously
detected
SW 15-4 – 8 When the remote machine cannot receive
signals in a proper level.
SW 17-4, 8 When an error occurs in the JBIG mode
SW 43-1 When SG3 communication error occurs
frequently
SW 43-4 – 6 When SG3 communication error occurs
frequently
SW 6-8 When an error occurs in phase B
SW 59-5 – 8 Setting is made referring to the distance
from the station when a communication
trouble occurs.
SW 44-1 – 4 When an error occurs in the SG3
communication.
SW 42-8 When an error occurs in the SG3
communication in FAX service, etc.
SW 16-1 – 4 To specified/unspecified destination
SW 52-5 When judged as "OK" though RTN is
received
SW 6-3
SW 7-6 When a document of 1m or longer is
received
SW 44-5 – 8 When fall-down occurs frequently in the
SG3 communication
SW 6-4 When an error occurs in phase B in
reception
SW 16-5, 6 When the line quality is poor and a fall-back
or an error occurs
SW 72-1 Change in the detection method of training
error
When reduction print is not made
When an index is attached to the reception
data
Usage