Optional Accessories - Makita LS1013 Instruction Manual

counterclockwise after loosening the adjusting screw.
Turn these two screws clockwise to shift it closer to the
side surface of the blade after loosening the adjusting
screw.
Refer to the section titled "Laser beam action" and adjust
the adjusting screw so that the cutting line on your
workpiece is aligned with the laser line.
NOTE:
• Check the position of laser line regularly for accuracy.
• Have the tool repaired by Makita authorized service
center for any failure on the laser unit.
Cleaning of the lens for the laser light
For model LS1013L, LS1013FL only (Fig. 59)
If the lens for the laser light becomes dirty, or sawdust
adheres to it in such a way that the laser line is no longer
easily visible, unplug the saw and remove and clean the
lens for the laser light carefully with a damp, soft cloth. Do
not use solvents or any petroleum-based cleaners on the
lens. (Fig. 60)
To remove the lens for the laser light, remove the saw
blade before removing the lens according to the
instructions in the section titled "Installing or removing
saw blade".
Loosen but do not remove the screw which secures the
lens using a screwdriver.
Pull out the lens as shown in the figure.
NOTE:
• If the lens does not come out, loosen the screw further
and pull out the lens again without removing the screw.
Replacing fluorescent tube
For LS1013F, LS1013FL only (Fig. 61)
CAUTION:
• Always be sure that the tool is switched off and
unplugged before replacing the fluorescent tube.
• Do not apply force, impact or scratch to a fluorescent
tube, which can cause a glass of the fluorescent tube
to be broken resulting in a injury to you or your
bystanders.
• Leave the florescent tube for a while immediately after
a use of it and then replace it. If not, you may burn
yourself.
Remove screws, which secure lamp box for the light.
Pull out the lamp box keeping pushing lightly the upper
position of it as illustrated on the left.
Pull out the fluorescent tube and then replace it with
Makita original new one.
Replacing carbon brushes (Fig. 62)
Remove and check the carbon brushes regularly. Replace
when they wear down to the limit mark. Keep the carbon
brushes clean and free to slip in the holders. Both carbon
brushes should be replaced at the same time. Use only
identical carbon brushes.
Use a screwdriver to remove the brush holder caps. Take
out the worn carbon brushes, insert the new ones and
secure the brush holder caps. (Fig. 63)
After use
• After use, wipe off chips and dust adhering to the tool
with a cloth or the like. Keep the blade guard clean
20
according to the directions in the previously covered
section titled "Blade guard". Lubricate the sliding
portions with machine oil to prevent rust.
• When storing the tool, pull the carriage toward you fully
so that the slide pole is thoroughly inserted into the turn
base.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Steel & Carbide-tipped saw blades
• Sub-fence R
• Vise assembly (Horizontal vise)
• Vertical vise
• Socket wrench 13
• Holder
• Dust bag
• Elbow
• Triangular rule
• Lock-off button (2 pcs.)
• Fluorescent tube (For LS1013F, LS1013FL)
• Kerf block
• Hex wrench (For LS1013L, LS1013FL)
• Dust box
NOTE:
• Some items in the list may be included in the tool
package as standard accessories. They may differ
from country to country.