Download
Share
Print this page
Honeywell Evohome Installation Manual
  1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Controller
  5. Evohome
  6. Installation manual

Honeywell Evohome Installation Manual

Controller
Hide thumbs Also See for Evohome:

Advertisement

Quick Links

Download this manual See also: User Manual
evohome
Installation
Guide

Advertisement

loading

Related Manuals for Honeywell Evohome

Summary of Contents for Honeywell Evohome

  • Page 1 Installation Guide...
  • Page 2 Controller ( R8810 ) Mixing Valve Controller evohome Controller Wall ( HM80 ) Bracket ( ATF300 ) evohome Controller Table Stand Room Temperature Sensor ( ATF100 or ATF200 ) ( HCW82 ) Room Temperature Sensor Radiator Controller ( HR92 )

  • Page 3: Before You Start

    Before you start Make sure you have all the devices you need for your system. If you used our ‘Design your evohome system’ guide, match each device to the room or zones in your plan. It’s a good idea to carry out all the mains electrical and other wiring work first.
  • Page 4 Step 1: Wire up your heating system Connect all mains powered devices to the heating system Step 2: Set up your evohome Controller Power up the evohome Controller and follow the on-screen instructions for your system Go to Installer Menu Go to Guided Configuration...

  • Page 5: Step 1: Wire Up The Heating System

    Some devices need mains power or to be connected to external equipment and it's best to wire up these items first to simplify the binding process later in the setup. The evohome controller will give on screen instructions when these should be powered up.
  • Page 6 Step 1: Wire up the heating system Wireless Relay Box (BDR91) If you’re fitting a Wireless Relay Box (BDR91) to your boiler, zone valve or Sundial valve Turn off at mains and isolate Mount the Wireless Relay Box on a non-metal surface at least the supply before starting 30cm from your boiler, other wireless device or metal objects Release the clip on the bottom to open the front cover...
  • Page 7 Installation Guide Wireless Cylinder Thermostat (CS92) If you’re fitting a Wireless Cylinder Thermostat (CS92) You will need to install the CS92 Transceiver and only one of the two sensors (CS92 Strap- on Sensor or CS92 Insertion Sensor). To fit the CS92 Strap-on Sensor...
  • Page 8 Step 1: Wire up the heating system Wireless Cylinder Thermostat (CS92) continued To fit the CS92 Insertion Sensor Fit in the cylinder immersion well with suitable fittings to provide strain relief and prevent accidental removal If the sensor doesn’t fit tightly in the immersion well fill the space with heat-conductive compound to ensure maximum heat transfer Install the CS92 Transceiver in a suitable location close...
  • Page 9 Installation Guide Remote Access Gateway (RFG100) If you’re fitting a Remote Access Gateway (RFG100) Connect the Remote Access Gateway to the home’s internet router using the ethernet cable supplied...
  • Page 10 Step 1: Wire up the heating system Mixing Valve Controller (HM80), Underfloor Heating Controller (HCE80/HCC80), OpenTherm Bridge (R8810) If you’re fitting a Mixing Valve Controller (HM80), Underfloor Heating Controller (HCE80/HCC80), OpenTherm Bridge (R8810) Refer to the installation instructions supplied with each device...

  • Page 11: Step 2: Set Up Your Evohome Controller

    Guided Configuration your evohome Controller will give you on-screen instructions to bind the other components to the evohome Controller – just follow the bind instruction for each device in this manual. In this section...
  • Page 12 After 30 minutes table stand or wall bracket. the evohome Controller will emit a beep to indicate that Place the evohome it should be replaced on the stand or wall bracket...

  • Page 13: Step 3: Power Up And Bind Devices

    Installation Guide Then to set up the evohome Controller Follow the on-screen instructions to set up the language, date and time Now choose the correct option for the system you’re installing: For a Base Pack or a Connected Pack and NO additional devices we recommended pressing ‘Home’...
  • Page 14 Step 2: Set up your Central Controller...
  • Page 15 If you bought a Base Pack or a Mobile Connected Pack, plus other devices, you need to power up all devices and then bind them to the evohome Controller using the ‘Installation Menu’. It may be easier to power up and bind some devices while they’re close to the evohome Controller –...
  • Page 16 You should receive a SUCCESS message on the green tick evohome Controller (if not go back and re-bind) 6. Press RADIATOR VALVE 7. If you want to control the The name of the allocated zone should appear on...
  • Page 17 Installation Guide Install the Radiator Controllers (HR92) Locate the room (zone) for the radiator controller Slide the locking mechanism to the unlock position Remove the adaptor from the bottom of the controller Unscrew the black wheel fully anticlockwise Remove any existing control on the radiator valve...
  • Page 18 4. Press STORED HOT You should receive a SUCCESS message on the WATER CONFIGURATION evohome Controller (if not go back and re-bind) 5. Press the green tick Choose the correct hot water valve type for the system you’re installing and follow the on screen instructions...
  • Page 19 Press and hold the button again for 5 seconds the wiring diagrams in the Appendix (until the red LED blinks slowly) On the evohome Controller press the green bind button You should receive a SUCCESS message on the evohome Controller (if not go back and re-bind) HOlD...
  • Page 20 You should receive a SUCCESS message on the If you are NOT following GUIDED CONFIGURATION evohome Controller (if not go back and re-bind) follow these steps on your evohome Controller display Now you need to set up a user account first: and download the smartphone app.
  • Page 21 Press and hold the button again for 5 seconds (until the red LED blinks slowly) On the evohome Controller press the green bind button You should receive a SUCCESS message on the evohome Controller (if not go back and re-bind)
  • Page 22 Press the up arrow – it should say COnt Press the power button once to send the binding signal to the evohome Controller You should receive a SUCCESS message on the evohome Controller (if not go back and re-bind) HOlD 3 SEC...
  • Page 23 Press and hold the button again for 5 seconds (until the red LED blinks slowly) On the evohome Controller press the green bind button You should receive a SUCCESS message on the evohome Controller (if not go back and re-bind)
  • Page 24 Power up and bind a Radiator Controller evohome Controller (HR80) If you are NOT following If you want to control the zone temperature with your evohome GUIDED CONFIGURATION Controller (the evohome Controller needs to be located in that follow these steps on your evohome Controller display zone) press YES, otherwise press NO and bind the sensor.
  • Page 25 HR80’s in the zone, do this to all of them). The screen should show a flashing RF icon On the evohome Controller press the green bind button Check that (all) the Radiator Controllers display SYNC. If a Radiator Controller does not display SYNC and...
  • Page 26 Press the power button once to send the binding signal to the evohome Controller You should receive a SUCCESS message on the evohome Controller (if not go back and re-bind) Make sure the zone you’re adding on the evohome HOlD...
  • Page 27 Press the bind button on the bottom right hand corner of the unit once. The red LED light will flash You should receive a SUCCESS message on the evohome Controller (if not go back and re-bind) CONTINUED ON NExT PAGE...
  • Page 28 On the evohome Controller, press the green bind button If the zone light turns solid green the binding is successful If the zone light turns solid red continue with these...
  • Page 29 Controller (HM80) A Mixing Valve Controller should only be fitted by a qualified If you are NOT following fitter. Unless you’re using the evohome Controller as a sensor, GUIDED CONFIGURATION you need to install a sensor (HCW82, HCF82 or DTS92)
  • Page 30 Press and hold both buttons on the Mixing Valve Controller for 4 seconds until the red light flashes On the evohome Controller press the green bind button You should receive a SUCCESS message on the evohome Controller (if not go back and re-bind)
  • Page 31 Installation Guide Step 4: System test Now that all the devices are bound to your evohome Controller and installed in their final locations, check that the system works properly and that all the devices are responding to commands from the evohome Controller.
  • Page 32 • The Relay Box will flash the green LED from 1 flash (poor) to 5 flashes (excellent) – no flashing means the Relay Box has not received a test signal from the evohome Controller Remote Access Gateway (RFG100) • The Gateway will flash the green LED from 1 flash (poor) to 5 flashes (excellent) –...
  • Page 33 Turn the dial to display RF CHECK Press the button The evohome Controller will display the signal strength (poor to excellent) and the Radiator Controller will display a signal strength bar and a rating from 1 (poor) to 5 (excellent) – 0 means the Radiator Controller has not received a test signal from the evohome Controller.
  • Page 34 Turn the adjustment dial clockwise (approx two full rotations) until TEST is displayed The evohome Controller will display the signal strength (poor to excellent) – nothing on the evohome Controller display means the Radiator Controller has not received a test signal from the evohome Controller.
  • Page 35 1 (poor) to 5 (excellent) – 0 means the Room Thermostat has not received a test signal from the evohome Controller. To exit test mode, press off on Room Thermostat for 5 seconds. It will exit automatically after 10 minutes.
  • Page 36 LED goes off (approx 30 seconds) The red LED will flash each time it sends a test message The evohome Controller will display the signal strength (poor to excellent) – no flashing means the Temperature Sensor has not received a test signal from the evohome Controller.
  • Page 37 The green light should come on. If it doesn’t, reinsert the batteries and try again The evohome Controller will display the signal strength (poor to excellent) and the transceiver should flash the red LED from 1 flash (poor) to 5 flashes (excellent) –...
  • Page 38 Step 4: System test...
  • Page 39 Once you’ve completed these steps you’re ready to start using evo. You can also make parameter adjustments in the evohome Controller to match the exact requirements of the heating system. The operation and functions of the each zone can also be adjusted.
  • Page 40 The user guide gives you instructions for personalising the settings on the evohome Controller. You can also make parameter adjustments on your evohome Controller to match the exact requirements of the heating system. These can be found in the Installer Menu.
  • Page 41 Adding and replacing components in an existing system Adding and replacing components in an existing system On the evohome Controller press and hold “Settings” for 3 seconds Press the green tick To change a device in a zone press ZONE SETTINGS and...
  • Page 42 Configuration and modification...
  • Page 43 Installation Guide Appendix Wiring diagrams, heating system schematics In this section Sample evo systems Wiring diagrams Safety information evohome Controller technical data...
  • Page 44 Appendix Sample evo systems Single zone The evohome Controller is the sensor for the whole home which is controlled to the same time and temperature schedule. This system also includes wireless connectivity, which is available for any configuration. Figure 1 Single...

  • Page 45: Evohome Installation Guide

    Installation Guide Honeywell Y plan 1 three-port mid- position valve The operation is identical to the S plan but it uses a single three-port or mid position valve. If a system has been set up and the relays are moved...

  • Page 46: Wiring Diagrams

    Appendix Wiring diagrams Connecting a wireless boiler relay A basic boiler Figure 5 Wiring for a basic boiler (not requiring Place link here a pump overrun). The relay powers the boiler live input. BDR91 A-B:5(3)A A-C:5(3)A 230V A B C 50-60Hz <5A A boiler that requires a permanent live...
  • Page 47 Installation Guide Connecting a two-port zone valve Figure 7 Connecting a BDR91 A-B:5(3)A two port zone valve A-C:5(3)A G/Y: Green/Yellow Earth wire 230V N L L A B C BL: Blue Motor Neutral 50-60Hz <5A BR: Brown Motor Live...
  • Page 48 Appendix Wiring diagrams continued Sundial or system valves Figure 9 Two port valves with a wired boiler. If a wireless boiler relay is S Plan: 2 two-port valves with a wired boiler used the Grey, Orange and feed to pump and boiler are not required.
  • Page 49 Installation Guide Y Plan: Three-port Mid position Figure 10 Mid position valve with a wired boiler (3 port) valve G/Yellow: Earth wire If a wireless boiler relay is used the Orange and BLUE: Motor Neutral feed to pump and boiler are not required.

  • Page 50: Safety Information

    This product has been designed for applications Hereby, Honeywell, declares that this as described within this document. For use evohome Controller is in compliance with outside of the scope as described herein, refer the essential requirements and other relevant to Honeywell for guidance. Honeywell cannot provisions of Directive 1999/5/EC.
  • Page 51 Installation Guide evohome evohome Controller technical data Electrical Power module Input voltage: 230VAC *10% Output voltage: 4VDC *0.2V, max 26W Room unit power 4VDC ±0.2V, max. 2.6W supply input Low voltage cable 10m, 1.0mm ; 5m, 0.5mm length (max) Battery type Type AA 1.2V NiMH 2000-2400mAh...
  • Page 52 For more information on Smart Heat Zoning for your home, visit: www.evohome.honeywell.com Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell Technologies Sàrl, ACS- ECC EMEA, Z.A. La Pièce 16, 1180 Rolle, Switzerland by its Authorised Representative Honeywell Inc.