Related Manuals for HIKVISION DS‐2CC5173P‐VF
Summary of Contents for HIKVISION DS‐2CC5173P‐VF
- Page 1 DS‐2CC5173P(N)‐VF Day / Night High‐definition Dome Camera User Manual V 1.2.0 Hikvision Digital Technology Co., Ltd. http://www.hikvision.com ...
- Page 2 Standard(s) for Safety, UL60950‐1. UL Certification does not cover the performance or reliability of the security or signaling aspects of this product. UL MAKES NO REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.” © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
- Page 3 EU Conformity Statement This product and ‐ if applicable ‐ the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC. 2002/96/EC (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info. 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: ww.recyclethis.info. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
- Page 4 Power Supply Hazardous Voltage: AC mains voltages are present within the power supply assembly. This device must be connected to a UL approved, completely enclosed power supply, of the proper rated voltage and current. No user serviceable parts inside the power supply. System Grounding (Earthing): To avoid shock, ensure that all AC wiring is not exposed and that the earth rounding is maintained. Ensure that any equipment to which this device will be attached is also connected to properly wir e grounded receptacles and are approved medical devices. d Power Connect an d Disconnect: The AC power supply cord is the main disconnect device to mains (AC power).The socket outlet shall be installed near the equipment and sha ll be readily accessible. Installation and Maintenance: Do not connect/disconnect any cables to or perform installation/maintenance on this device during an electrical storm. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
- Page 5 eliminate the interference or discontinue the use of this equipment. Lead Content: Please re cycle this device in a responsible manner. Refer to local environmental regulations for proper recycling; do not dispose of device in unsorted municipal waste. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
- Page 6 4. Please make sure that the plug is firmly connected to the power socket. 5. When the product is mounted on wall or ceiling, the device shall be firmly fixed. 6. If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center. 7. If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the camera yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.) © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
- Page 7 The average time varies because of differences between operating environment and using history, so regular checking is recommended for all the users. Please contact with your dealer for more details. 11. Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
-
Page 8: Table Of Contents
2.2 In ceiling mounting with gang box ......................12 2.3 In ceiling mounting without gang box....................13 Chapter 3 Menu Description..........................16 3.1 Menu Interface ............................16 3.2 Menu Details ............................16 3.2.1 Camera ID Settings...........................16 3.2.2 Lens Type Settings..........................17 3.2.3 WHITE BAL Settings..........................18 3.2.4 BLC/ECLIPSE Settings........................19 3.2.5 DAY / NIGHT Settings ........................20 3.2.6 Shutter Settings..........................21 3.2.7 AGC Settings.............................21 3.2.8 Synchronization..........................21 3.2.9 Language ............................21 3.2.10 Special Function ..........................21 3.2.11 Exit Setting .............................28 Appendix ................................29 Specification..............................29 Dimension ..............................30 © Hikvision Digital Technology Co., Ltd. All Rights Reserved. -
Page 9: Chapter 1 Introduction
Advanced 3‐axis design to meet different mounting requirements Advanced double‐plate design to guarantee CCD heat dissipation and image quality. 1.2 Function Summary Motion Detection: In the user‐defined motion detection surveillance area, the moving object will trigger alarm. User can select suitable sensitivity level according to corresponding environment. Privacy Mask: In the surveillance area, user can cover areas to protect other’s privacy. The number of privacy mask areas is up to 8. DAY&NIGHT Auto Switch: The camera will display color image in the daytime and become monochrome automatically at night. AGC: When the object being shot looks dim, please turn on AGC to enhance brightness. To output standard © Hikvision Digital Technology Co., Ltd. All Rights Reserved. - Page 10 BLC OFF BLC ON © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
-
Page 11: Chapter 2 Installation
User Manual of Day/Night High‐definition dome Camera Chapter 2 Installation Before mounting, please make sure that the device in the package is in good condition and all the assembly parts are included. 2.1 Ceiling mounting Note: Please ensure that the wall is strong enough to withstand three times weight of the camera and then install the camera securely. If the wall is not strong enough, the camera may fall and cause serious damage. 1. Hold the base of the dome camera. Rotate the lower dome anticlockwise to take it down. Then, take down the inner black lower dome. Figure 2.1.1 Take down the lower dome and inner black dome 2. Use the supplied drill template to position the holes on the wall where the dome camera should be installed. Figure 2.1.2 Position the holes 3. Attach the base of dome camera to the ceiling with self‐tapping screws as shown in figure 2.1.3. Note: Please use expansion screw first if the dome camera is mounted to cement wall. And the positions of the expansion screws should match with positions of dome’s mounting holes. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. - Page 12 User Manual of Day/Night High‐definition dome Camera Figure 2.1.3 Fix the base to the wall 4. Rotate the dome drive clockwise into the base, and fix the lock screw as shown in figure 2.1.4. Figure 2.1.4 Fix the dome drive to the wall 5. Adjust the lens to a surveillance area as needed and get clear image. Advanced 3‐axis design allows this dome camera to be adjusted 0‐355°horizontally and 0‐180°vertically to meet different mounting requirements. Note: Please loosen the lock screw in the lens before adjusting the lens position and fix the screw if the lens position is confirmed. Figure 2.1.5 Adjust the lens 6. At last, rotate the lower domes clockwise back to the dome drive. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
-
Page 13: In Ceiling Mounting With Gang Box
Note: Please ensure that the wall is strong enough to withstand three times weight of the camera and then install the camera securely. If the wall is not strong enough, the camera may fall and cause serious damage. 1. Rotate the lower dome anticlockwise to take it down. Then, take down the inner black lower dome. Loosen the screws on the mounting base. Take down the base. Figure 2.2.1 Take down the lower dome and inner black dome 2. Use the supplied drill template to position the holes on the wall where the dome camera should be installed. Figure 2.2.2 Position the holes © Hikvision Digital Technology Co., Ltd. All Rights Reserved. -
Page 14: In Ceiling Mounting Without Gang Box
Figure 2.2.4 Install dome drive and adjust lens At last, install the lower domes back to the dome drive. Figure 2.2.5 Finish the installation 2.3 In ceiling mounting without gang box Note: Please ensure that the wall is strong enough to withstand three times weight of the camera and then install the camera securely. If the wall is not strong enough, the camera may fall and cause serious damage. 1. Rotate the lower dome anticlockwise to take it down. Then, take down the inner black lower dome. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. - Page 15 Figure 2.3.2 Position the holes 3. Attach the flush mounting base to the ceiling with screws. Ceiling Flush Mounting Base Figure 2.3.3 Attach base to ceiling 4. Attach the dome drive to the base and use screws to fix it. Adjust the lens to a surveillance area as needed and get clear image. Fix the lock screw into the lens then. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
- Page 16 User Manual of Day/Night High‐definition dome Camera Figure 2.3.4 Install dome drive and adjust lens At last, install the lower domes back to the dome drive. Figure 2.3.5 Finish the installation © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
-
Page 17: Chapter 3 Menu Description
User Manual of Day/Night High‐definition dome Camera Chapter 3 Menu Description 3.1 Menu Interface Press menu button, the OSD menu will show on the screen. Press up/down buttons to move the cursor, left/right buttons to select the different options; 3.2 Menu Details 3.2.1 Camera ID Settings Press up/down to move cursor to “CAM ID”, press left/right to enable or disable this setting. ON/OFF: Display the camera ID on the screen or not. Select “On” , and press confirm button to enter the “CAM ID “menu. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. -
Page 18: Lens Type Settings
3.2.2 Lens Type Settings Press up/down to move the cursor to “LENS”, and press left/right to select the lens type as ELC or ALC. ELC uses auto electronic shutter to adjust the brightness; ALC uses auto iris to adjust the brightness; Note: ELC: auto shutter, fixed iris; ALC: auto iris, fixed shutter. Select ELC and press confirm button then the “ELC Setup” menu is shown on the screen. Press up/down to move the cursor to the “VALUE”, press left/right to adjust brightness, move the cursor to “RETURN” and press confirm button to return to the previous menu. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. -
Page 19: White Bal Settings
ATW1: Auto traced balance mode 1, built‐in indoor environment. algorithm for automatic white balance setting. Usually used for ATW2: Auto traced balance mode 2, built‐in outdoor environment. Manual WB setting is as below: Select “MANUAL” and the menu is displayed on the screen: © Hikvision Digital Technology Co., Ltd. All Rights Reserved. -
Page 20: Blc/Eclipse Settings
3.2.4 BLC/ECLIPSE Settings BLC: Back Light Compensation Move cursor to “BLC/ECLIPSE”, press left/right to “BLC” and press confirm button to enter the BLC SETUP menu. And the menu is displayed on the screen: Move cursor to “VALUE” to select LOW, MID or HIGH. Move cursor to “AREA”, press confirm button to enter the submenu. First, press direction button to set the BLC area position as up, down, left, right and middle, then press confirm button to set the size of BLC area in the same way. Press confirm button to choose “RET” to return to the previous menu or “AGAIN” to reset position and size. Move cursor to “DEFAULT” to set VALUE and AREA back to default setting. Move the cursor to “RETURN”, press confirm button to return to the previous menu. ECLIPSE Move cursor to “BLC/ECLIPSE”, press left/right to “ECLIPSE” and press confirm button to enter ECLIPSE SETUP menu. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. -
Page 21: Day / Night Settings
User Manual of Day/Night High‐definition dome Camera Value setting: Press left/ right to adjust the value, value ranges from 0‐8. ECLIPSE MODE: DAY, ALL DAY and NIGHT modes can be selected. AREA setting: The position and size of ECLIPSE area can be set in the same way as BLC’s area setting. DEFAULT: Move cursor to “DEFAULT” to set VALUE, ECLIPSE MODE and AREA back to default setting. Move the cursor to “RETURN”, press confirm button to return to the previous menu. 3.2.5 DAY / NIGHT Settings Press up /down to move the cursor to “DAY/ NIGHT”, and press left / right to select DAY, NIGHT and AUTO. Auto Setting: Select “AUTO” and press confirm button to enter the submenu: DELAY: Range from 0 to 63. DAY→NIGHT/ NIGHT→DAY: Press left/right buttons to set the threshold value of conversion between DAY mode and NIGHT mode from 0‐255 selectable. Move the cursor to “RETURN” and press confirm button to return to the previous menu. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. -
Page 22: Shutter Settings
× 256, 1/100000, 1/10000, 1/5000, 1/2000, 1/1000, 1/500, 1/250, FLK, 1/50. Note: FLK means “Flickerless”. It is used to eliminate the image flicker when the PAL system camera in 60Hz illuminant or the NTSC system camera in 50Hz illuminant. 3.2.7 AGC Settings “AGC” includes OFF, LOW, MIDDLE and HIGH. Press left/right to select desired mode. Note : If the DAY/NIGHT mode is auto, there are only LOW, MIDDLE and HIGH selectable. 3.2.8 Synchronization Internal and power synchronization are both available. When using DC12V power supply, it displays internal synchronization and is not adjustable. When using AC24V, user can select either internal or power synchronization. 3.2.9 Language English is the default language. 3.2.10 Special Function Move cursor to “SPECIAL” , press confirm button and the menu will be displayed on the screen. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. - Page 23 VIDEO Setting Move cursor to “VIDEO”, press confirm button and the menu will be displayed on the screen. GAMMA Move cursor to “GAMMA”, and press left / right to set GAMMA value which is used to adjust brightness disparity between output video signal and acquisition video signal. GAMMA values include: USER and range from 0.05 to 1.00 with 0.05 interval. When the value is 1.00, the brightness will not be adjusted. FREEZE Freeze current picture if it is ON. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
- Page 24 User Manual of Day/Night High‐definition dome Camera Motion Move cursor to “MOTION”, press left/right to turn it on or off, press confirm button to enter the submenu: AREA: Move cursor to “AREA” and press left/right to select from four areas. AREA DISPLAY: Press left or right to turn it on or off. If it is off, motion detection is disabled of this area. If it is on, press confirm button to enter the submenu to set size and position of the area. VALUE: Select sensitivity value from 0 to 40. The value is higher, the sensitivity is greater. MOTION DISP: Press left/right to turn it on or off. There will be color displayed on the screen when motion detection is triggered. Move the cursor to “RETURN”, press confirm button to return to the previous menu. MIRROR Move the cursor to “MIRROR”, press left/right to select “MID”,”H”,”V” or “OFF”. “H” represents horizontal, “V” represents vertical. Zoom Move cursor to “ZOOM”, press left/right to select “ON”, press confirm button to the submenu: © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
- Page 25 User Manual of Day/Night High‐definition dome Camera RATE: The maximum zoom rate is 32. Press left/right button to zoom in/out. “H” and “V” are available when the image is magnified. Then, adjust the “H” and “V” values to control the movement on the image. The value is from ‐100 to 100 adjustable. Move the cursor to “RETURN”, press confirm button to return to the previous menu. 3DNR User can turn on or off the digital noise reduction. If the 3DNR is turned ON, the processor will analyse and process the digital signal to reduce the noise. Press left/right to select “ON” and press confirm button to enter DNR SETUP menu: VALUE: There are 0‐100 levels selectable. The higher value is, the better DNR effect is. Move the cursor to “RETURN”, press confirm button to return to the previous menu. POS/ NEG Move cursor to “POS / NEG”, and press left / right to select POS or NEG. If POS is selected, the video will be normal. If NEG is selected, the video will be negative. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
- Page 26 User Manual of Day/Night High‐definition dome Camera SHARPNESS Sharpness is adjustable from 0 to 31. Y Brightness is adjustable from 0 to 255. C Press confirm button to enter C GAIN menu: Press up/down buttons to move the cursor to “C GAIN”. Press confirm button to enter C GAIN menu: BLUE: Blue value ranges from 0 to 100. RED: Red value ranges from 0 to 100. Move the cursor to “RETURN”, press confirm button to return to the previous menu. DEFECT setting: Move cursor to “DEFECT”, press confirm button to DEFECT SETUP menu: RATE: There are ×4, ×8, ×16, ×32, ×64 optional. VALUE: Range from 1 to 6. Value represents the size of . defect dot © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
- Page 27 Move cursor to “DWDR”, it is unavailable in the default setting. Press left/right to select INDOOR or OUTDOOR mode. INDOOR mode: LOW‐LEVEL: values range from 0‐15, press left/right to change it. HIGH‐LEVEL: values range from 0‐15, press left/right to change it. Move the cursor to “RETURN”, press confirm button to return to the previous menu. OUTDOOR mode: LOW‐LEVEL: Values range from 0‐15, press left/right to change it. HIGH‐LEVEL: Values range from 0‐15, press left/right to change it. Move the cursor to “RETURN”, press confirm button to return to the previous menu. PRIVACY setting: Move cursor to “PRIVACY”, press confirm button and the menu is displayed on the screen: © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
- Page 28 User Manual of Day/Night High‐definition dome Camera AREA: Move cursor to “AREA”. There are 8 default areas selectable. AREA DISPLAY: Select one area number and turn its “AREA DISPLAY” on. Press confirm button to enter the submenu to set size and position of the area. COLOR: The color of area can be changed by selecting the color number which ranges from 0 to 15. RETURN: Move the cursor to “RETURN”, press confirm button to return to the previous menu. SLOW SHUTTER Move cursor to “SLOW SHUTTER”, press left or right to turn it on/off. If it is on, press confirm button to the submenu: SLOW SHUTTER: × 2, × 4, ×8, ×16, ×32, ×64, ×128, ×160, ×256. RETURN: Move the cursor to “RETURN”, press confirm button to return to the previous menu. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
-
Page 29: Exit Setting
User Manual of Day/Night High‐definition dome Camera 3.2.11 Exit Setting Move cursor to “EXIT” , and press left / right to select from SAVE, CANCEL and DEFAULT. Then press “enter” to exit the menu. CANCEL: Press confirm button to cancel the setting parameter and exit the menu. SAVE: Press confirm button to save the setting parameter and exit the menu. DEFAULT: Press confirm button to restore the factory default value and exit the menu. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. -
Page 30: Appendix
IR cut filter with auto switch Horizontal Resolution 560 TVL (Color), 600 TVL (B/W) Synchronization Internal/Power synchronization 1Vp‐p composite output (75 Ω/BNC); Video Output Test monitor out [1Vp‐p composite output (75 Ω/BNC), device line] S/N Ratio More than 52 dB Menu Camera ID On/Off (15 letters, adjusted position) Auto Gain Low/Middle/High/Off D/N Mode Auto /Day/Night Auto White Balance ATW 1/ATW 2/Manual/Auto control Privacy Mask On/Off, maximum 8 zones Motion Detection On/Off BLC Back light area/ Intensity/Off Eclipse Intensity Value © Hikvision Digital Technology Co., Ltd. All Rights Reserved. -
Page 31: Dimension
User Manual of Day/Night High‐definition dome Camera Digital WDR Indoor/Outdoor/Off Anti‐flicker On/Off Language English/Chinese Gamma Correction, Digital Zoom, Digital Noise Reduction, Video POS/NEG ,Mirror, Sharpness, Y, C, Blemish Detection General ‐10 °C ‐ 60 °C (14 °F ‐ 140 °F) Operating Conditions Humidity 90% or less (non‐condensing) Power Supply 24 V AC ± 10%, 12 V DC ± 10% Max. 4 W Power Consumption (Max. 4.5 W with IR cut filter on) Dimension Φ 136 × 101 mm (Φ 5.35” × 3.98”) Weight 800 g (1.76 lbs) Dimension Unit: mm © Hikvision Digital Technology Co., Ltd. All Rights Reserved. - Page 32 User Manual of Day/Night High‐definition dome Camera First Choice for Security Professionals © Hikvision Digital Technology Co., Ltd. All Rights Reserved.