Honeywell LYNXRPK-2 - Wireless Self-Contained Security Syste - LYNXRPK-2 - Wireless Self-Contained Security System Installation And Setup Manual page 26

LYNXR-2 Series Installation and Setup Guide
Data Field Descriptions
✻
Field *47 is used to program different options in the LYNXR-2 and LYNXR-2SIA controls. Please
Fields 47:
be sure that you use the correct field for the control being installed.
✻47
Phone System Select
LYNXR-2 SELECTIONS
Central Dialing Mode
Station Pulse Tone
No 0 = No 1 = No
WATS Speaker Speaker
Phone Phone
WATS 2 = No 3 = No
Speaker Speaker
Phone Phone
LYNXR-2SIA SELECTIONS
Central Dialing Mode
Station Pulse Tone
No 0 = No 1 = No
WATS Speaker Speaker
Phone Phone
Call Wait Call Wait
Cancel Cancel
Disabled Disabled
WATS 2 = No 3 = No
Speaker Speaker
Phone Phone
Call Wait Call Wait
Cancel Cancel
Disabled Disabled
No 8 = No 9 = No
WATS Speaker Speaker
Phone Phone
Call Wait Call Wait
Cancel Cancel
Enabled Enabled
WATS 10 = No 11 = No
Speaker Speaker
Phone Phone
Call Wait Call Wait
Cancel Cancel
Enabled Enabled
✻48
Report Format for Primary/
Secondary
Primary
See choices below
0 = 3+1; 4+1 ADEMCO Low Speed Standard
1 = 3+1; 4+1 Radionics Standard
2 = 4+2 ADEMCO Low Speed Standard
3 = 4+2 Radionics Standard
5 = ADEMCO Contact ID® Reporting with 10-digit subscriber
account number
6 = 4+2 ADEMCO Express
7 = ADEMCO Contact ID® Reporting with 4-digit subscriber
account number
8 = 3+1; 4+1 ADEMCO Low Speed Expanded
9 = 3+1; 4+1 Radionics Expanded
Pulse Tone
4 = With 5 = With
Speaker Speaker
Phone Phone
6 = With 7 = With
Speaker Speaker
Phone Phone
Pulse Tone
4 = With 5 = With
Speaker Speaker
Phone Phone
Call Wait Call Wait
Cancel Cancel
Disabled Disabled
6 = With 7 = With
Speaker Speaker
Phone Phone
Call Wait Call Wait
Cancel Cancel
Disabled Disabled
12 = with 13 = With
Speaker Speaker
Phone Phone
Call Wait Call Wait
Cancel Cancel
Enabled Enabled
14 = With 15 = With
Speaker Speaker
Phone Phone
Call Wait Call Wait
Cancel Cancel
Enabled Enabled
Secondary
See choices below
This option is used to enter the correct type of phone dialing
(pulse or tone), and to select the correct WATS line option for
the Central Station. This option is used to activate the Speaker
Phone option. For the LYNXR-2SIA it is also used to disable
call waiting.
Note: If using pulse dialing, you must enter the numbers slowly in
order to allow the pulse dialer time to operate.
LYNXR-2SIA ONLY
Call waiting warning tones can interfere with Central stations
reporting. The Call Waiting Cancel option should be selected if
the reporting phone line has call waiting service. The Call
Waiting Cancel command must also be programmed in Field
✻
40. If the Call Waiting Cancel feature is enabled, make sure to
enter Call Waiting Cancel command in Field
depends on a telephone service provider.
Important Note: If Call Wait Cancel is disabled in Field
Call Waiting Disable command is entered in Field
40, this will prevent successful communication
✻
to the central station when used on a non-call
waiting line.
Note: PABX number and operation of the control panel with a
PBX system cannot be used if the Call Waiting Cancel
option has been enabled in Field
✻
Enter as the 4th digit of
reporting is to be used. (For an explanation of these formats, see
the System Communication section of this manual.)
Notes: (1) The maximum number of alarm and alarm restore
reports during one armed period is determined by field
✻ 92.
(2) If Option 5 is selected a 10-digit account number must
be entered in Fields ✻ 43 or ✻ 44.
(3) Option 5 or 7 (ADEMCO Contact ID® Reporting) must
be selected for AAV.
- 26 -
✻
40. The command
47.
✻
✻ ✻
43 through 44, if 3+1 dialer
47, and
✻