Makita RM350D Setup Manual page 29

NOTE: The maximum probability value that can be entered will be displayed in the left of entry area of each profile. Enter the value that is smaller
than the maximum value. If you enter the value beyond the allowable value, it will be replaced with the maximum value.
6. Select [Test] and execute test operation before registering the settings.
The Robotic Mower travels along the selected wire.
The Robotic Mower stops automatically after the distance you enter.
NOTE: The confirmation is finished if the Robotic Mower departs from the charging station and stops at the designated point.
7. Press the "STOP" button.
The display cover opens.
8. Select [Yes] to register or [No] to cancel the registration when the confirmation screen asking whether to register the test run departure method
is displayed.
If you select [No], you need to start the setting from the beginning again.
Checking boundary wire installation
Check that the boundary wire is installed correctly.
1.
Hold the grip of the Robotic Mower and move the Robotic Mower by hand so that it faces the boundary wire.
► Fig.46: 1. Boundary wire
2. Press the "STOP" button.
The display cover opens.
3. Press the button, select [Auto mowing] and press the
4. Close the display cover.
The Robotic Mower starts mowing and travels toward the boundary wire.
5. Check that the Robotic Mower changes direction at the boundary wire and continues mowing.
► Fig.47: 1. Boundary wire
6. Press the "STOP" button.
The Robotic Mower stops.
7. Turn off the power switch of the Robotic Mower and carry it to another place, and then turn on the switch. Check that the Robotic Mower oper-
ates similarly even at other boundary wire locations.
Returning the Robotic Mower to the charging station
[Top menu] > [Park] > [Stay at charging station]
This procedure is not necessary when a guide wire is installed. Proceed to [Checking guide wire installation]. Perform this procedure when using
the Robotic Mower without installing a guide wire.
Return the Robotic Mower to the charging station.
NOTE: By default, the Robotic Mower preferentially searches for signals from the guide wire and returns to the charging station according to sig-
nals of the guide wire. Even if there is not any guide wire in your work area, the Robotic Mower first continues to search for signals from the guide
wire for a preset priority search time. After the priority search time has elapsed, the Robotic Mower then researches for signals from the boundary
wire and returns to the charging station according to signals of the boundary wire. If you do not want to lay down the guide wire, we recommend
changing the priority search time for the guide wire. For details, see "Setting the active search period for the guide signal" in the instruction
manual.
1.
Press the button on the control panel.
The sub menu appears.
► Fig.48
2. Select [Stay at charging station].
Press the key, and the message [Close the display cover to return to the charging station.] appears.
3. Close the battery cover.
Check that the Robotic Mower returns to the charging station.
Checking guide wire installation
Check that the guide wire is installed correctly.
1. With the power turned off, hold the grip of the Robotic Mower and move the Robotic Mower by hand so that it faces the guide wire.
► Fig.49: 1. Guide wire
2. Press the "STOP" button.
The display cover opens.
3. Press the button, select [Stay at charging station], and press the
4. Close the display cover.
The Robotic Mower starts mowing navigation toward the guide wire.
5. Check that the Robotic Mower changes direction near the guide wire, navigates along the guide wire toward the charging station, and docks
with the charging station.
NOTE: After the Robotic Mower detects the guide wire, it will run along the left side of the guide wire.
This completes the installation and operation checks. For the detailed usage of this product, refer to the Instruction Manual of this product.
key.
key.
29 ENGLISH