Wall Mounting - Honeywell Unitary Installation Instructions Manual

Controller-230 vac
Table of Contents

Advertisement

HONEYWELL UNITARY CONTROLLER - 230 VAC - INSTALLATION INSTRUCTIONS
3. Hold the controller as shown in below image and
Mount the controller onto the DIN rail.
18
19
2
21
22
23
32
33
34
35
36
37 38
18
19
2
21
22
23
32
33
34
35
36
37 38
C01
C
CO2
CO3
C
CO4
IO13
C
IO14 IO15
C IO16
UIO
UIO
24VDC
O1
C
IO2 IO3
C
IO4 IO5
C
IO6 IO7
C
IO8
C
OUT
IO9
C
IO1
IO11 C IO12
52
53
54
55
56
57
58
59
6
61
62
63
64
65
66
67
68
69
7
71
72
52
53
54
55
56
57
58
59
6
61
62
63
64
65
66
67
68
69
7
71
72
Fig. 8 Controller mounting on DIN Rail

Wall Mounting

1. Extend all red clips to the screw mounting position
by inserting the flat blade screwdriver at a marked
location and move up the nod from the lower slot
to the upper slot as shown in figure 9.
Screw
Mounting
Position
Fig. 9 Screw Mounting Position
2. Hold the controller along the wall and mark drilling
locations through the screw red clip slots, as
shown in figure 10.
Fig. 10 Drill mark location
31-00610-01
1.
2.
Red Clip
Drill mark
location
3. Remove the controller from the wall and drill four
holes at the marked locations.
Large: 6.3 inches (160 mm)
Small: 4.5 inches (110 mm)
1
2
3
4
5
6
7
8
9
1
11 12 13 14 15
18 19
2
21 22 23
1
2
3
4
5
6
7
8
9
1
11 12 13 14 15
18 19
2
21 22 23
L
N
NC1 NO1 IN1 NC2 NO2 IN2 NC3 NO3 IN3 NC4 NO4 IN4
CO1
C
CO2
CO3
C
CO4
POWER 230V
DO RELAY
DO CHP
1
RS485
RS485 1
POW24
SYLK
UIO
24VDC
PORT1
PORT2
+
-
COM
V
WM1 / 2
IO1 C IO2 IO3 C IO4 IO5 C IO6 IO7 C IO8 C
OUT
10/100 SWITCHED
45
46
47 48 49 50 51 52 53
54
55 56 57 58 59
6
61 62 63
64
RS485 1
45
46
47 48 49 50 51 52 53
54
55 56 57 58 59
6
61 62 63
64
Fig. 11 Mounting and Dismounting
4. Insert anchors into the four mounting screw holes.
5. Place the controller on the wall/panel so that the
holes are aligned. Insert the screws into the top-
side holes first and fasten them with a screwdriver.
6. Insert the screws into the bottom hole and fasten
them with a screwdriver.
NOTE:
It is recommended to use the 6/18 1-inch pan
head Phillips tapping screws.
12
32 33 34 35 36 37 38
4.8 inches
32 33 34 35 36 37 38
IO13 C IO14 IO15 C IO16
UIO
(121.6 mm)
IO9
C
IO1
IO11 C IO12
65
66 67 68 69
7
71 72
65
66 67 68 69
7
71 72

Advertisement

Table of Contents
loading

Table of Contents