Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita TD003GM201
Summary of Contents for Makita TD003GM201
- Page 1 INSTRUCTION MANUAL Cordless Impact Driver TD003G Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: TD003G Fastening capacities Machine screw M4 - M8 Standard bolt M5 - M16 High tensile bolt M5 - M14 No load speed (RPM) 4 (Max impact mode) 0 - 3,700 min 3 (Hard impact mode) 0 - 3,200 min 2 (Medium impact mode) 0 - 2,100 min 1 (Soft impact mode) -
Page 3: Safety Warnings
Intended use EC Declaration of Conformity The tool is intended for screw driving in wood, metal For European countries only and plastic. The EC declaration of conformity is included as Annex A to this instruction manual. Noise The typical A-weighted noise level determined accord- ing to EN62841-2-2: SAFETY WARNINGS Sound pressure level (L ) : 95 dB (A) Sound power level (L ) : 106 dB (A) Uncertainty (K) : 3 dB (A) - Page 4 Personal safety Power tool use and care Stay alert, watch what you are doing and use Do not force the power tool. Use the correct common sense when operating a power tool. power tool for your application. The correct power tool will do the job better and safer at the Do not use a power tool while you are tired or under the influence of drugs, alcohol or med- rate for which it was designed.
- Page 5 WARNING: DO NOT let comfort or familiarity 12. Use the batteries only with the products with product (gained from repeated use) replace specified by Makita. Installing the batteries to strict adherence to safety rules for the subject non-compliant products may result in a fire, exces- product. sive heat, explosion, or leak of electrolyte.
-
Page 6: Functional Description
SAVE THESE INSTRUCTIONS. and a personal injury. To remove the battery cartridge, slide it from the tool CAUTION: Only use genuine Makita batteries. while sliding the button on the front of the cartridge. Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery bursting causing fires, personal injury and damage. It will also void the Makita warranty for the Makita tool and charger. Tips for maintaining maximum battery life Charge the battery cartridge before completely discharged. - Page 7 ► 1 . Indicator lamps 2. Check button Charge the battery(ies) or replace it/them with recharged battery(ies). Indicator lamps Remaining Let the tool and battery(ies) cool down. capacity If no improvement can be found by restoring protection system, then contact your local Makita Service Center. Lighted Blinking Switch action 75% to 100% 50% to 75% CAUTION: Before installing the battery car- tridge into the tool, always check to see that the...
-
Page 8: Electric Brake
► 1 . Reversing switch lever Electric brake This tool is equipped with an electric brake. If the tool consistently fails to quickly stop after the switch trigger is released, have the tool serviced at a Makita service center. Fig.6 ► 1 . Button 2. Switch panel... -
Page 9: Light Mode
Light mode You can use the tool as a handy light. Turning on / off the light mode To turn on the light, set the reversing switch lever in the neutral position and pull the switch trigger. The lamp keeps lighting up for approximately one hour. To turn off the light mode, pull the switch trigger again or depress the reversing switch lever. NOTE: You cannot change the application mode while the light mode is on. - Page 10 Changing the impact force You can change the impact force in five steps: 4 (max), 3 (hard), 2 (medium), 1 (soft) and T mode. This allows a tightening suitable to the work. “T” is a special mode for fastening self-drilling screws. This mode helps to prevent the screws from over-tightening. It also accomplishes quick operation and good finish at the same time. The tool drives a screw with high-speed rotation and stops soon after the tool starts to impact. The level of impact force changes every time you press the button or button You can change the impact force within approximately one minute after releasing the switch trigger.
- Page 11 Application mode Maximum blows Purpose Example of application (Impact force grade displayed on panel) T mode * – Driving self-drilling screws to a thin Tightening self-drilling screws. metal plate with good finish. (The tool stops rotating soon after impact starts.) : The lamp is on. When the tool rotates counterclockwise, the impact per minute is the same as in 4 (max) mode, 4,100 min min).
-
Page 12: Installing Hook
To remove the driver bit, pull the sleeve in the direction Using hole of the arrow and pull the driver bit out. WARNING: Never use the hanging hole for unintended purpose, for instance, tethering the tool at high location. Bearing stress in a heavily loaded hole may cause damages to the hole, result- ing in injuries to you or people around or below you. -
Page 13: Maintenance
Never use gasoline, benzine, thinner, (510) alcohol or the like. Discoloration, deformation or cracks may result. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 1. Fastening time (second) 2. Fastening torque Hold the tool firmly and place the point of the driver bit in the screw head. Apply forward pressure to the tool to the extent that the bit will not slip off the screw and turn the tool on to start operation. -
Page 14: Optional Accessories
OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regard- ing these accessories, ask your local Makita Service Center. • Driver bits • Socket bits •... - Page 16 Jan-Baptist Vinkstraat 2, Makita Europe N.V. 3070 Kortenberg, Belgium 3-11-8, Sumiyoshi-cho, Makita Corporation Anjo, Aichi 446-8502 Japan 885A11-226 www.makita.com 20220803...