Makita DCX200 Instruction Manual page 10

Meaning of the indicator lamp
Indicator lamps
Lighted Off
(The lamps go off after a certain period.)
Installing or removing the battery
cartridge
Only when using the battery cartridge used with
battery holder
CAUTION:
Always switch off the device
before installing or removing the battery
cartridge.
CAUTION:
Hold the battery holder and the
battery cartridge firmly when installing or remov-
ing the battery cartridge. Failure to hold the battery
holder and the battery cartridge firmly may cause
them to slip out of your hands and result in damage
to the battery holder and battery cartridge and/or a
personal injury.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator as
shown in the figure, it is not locked completely.
To remove the battery cartridge, slide it from the battery
holder while pressing the button on the front of the
cartridge.
► Fig.4: 1. Red indicator 2. Button 3. Battery cartridge
4. Battery holder
CAUTION:
Always install the battery car-
tridge fully until the red indicator cannot be seen.
Otherwise the battery cartridge may accidentally
fall out of the battery holder, causing injury to you or
someone around you.
CAUTION:
Do not forcibly install the battery
cartridge. If the battery cartridge does not slide in
easily, it is not being inserted correctly.
Battery pocket
The battery can be stored in the battery pocket.
Connect the plug of power cable to the battery. Then
put the battery into the battery pocket and fasten the
fastener.
► Fig.5: 1. Power cable 2. Plug 3. Battery pocket
Remaining
capacity
Blinking
100%
(The charging
is finished)
50% to 100%
25% to 50%
Less than
25%
NOTE: The battery holder (with battery cartridge)
cannot be stored in the battery pocket.
Attaching the battery holder
You can hang the battery holder on your waist belt.
To prevent the battery holder from dropping acciden-
tally, attach a strap using the strap hole and secure it.
1. Feed the plug through the hole in the battery
pocket and pull it through to the inside of the base layer
shirt.
► Fig.6: 1. Power cable 2. Hole 3. Battery pocket
4. Plug
2. Attach the belt hook of the battery holder to your
waist belt. Connect the plug of the power cable to the
battery holder.
► Fig.7: 1. Belt hook 2. Battery holder 3. Waist belt
4. Power cable
The battery holder has an anti-drop function. When
removing the battery holder from the belt, pull up the
battery holder while pressing the unlock button.
► Fig.8: 1. Unlock button
FUNCTIONAL
DESCRIPTION
Power button
To turn on the base layer shirt, connect all the cables,
press and hold the power button on the battery or bat-
tery holder. To turn off, press and hold the power button
on the base layer shirt.
NOTE: The power level indicator on the battery
holder is not used with the base layer shirt. Only the
power level indicator 4 will light up when using the
base layer shirt.
► Fig.9: 1. Power button 2. Power level indicator
NOTE: The battery and the battery holder automat-
ically turns off approximately 1 hour after the base
layer shirt is turned off.
Temperature adjustment
CAUTION:
For continuous operation, set the
temperature setting to "low" (blue). If the base
layer shirt is overheated, the base layer shirt may
cause a malfunction and cause an injury.
There are three temperature settings (high, medium,
low). When you switch on the base layer shirt, the tem-
perature is set to "low". Each time you press the power
button, the temperature setting changes as shown in
the figure. The color of the power button shows the
current setting.
► Fig.10: 1. Blue: "low" 2. Red: "high" 3. White:
"medium"
10 ENGLISH