Honeywell OneWireless XYR 6000 Professional Installation Manual page 34

7. Equivalent Isotropically Radiated Power (EIRP)
7.1. EIRP LIMITS
Notes for Table 7-3 and Table 7-4
1. The Model Number of any instrument may be found on the identification name plate located on the outside
of the XYR 6000 transmitter. The values in the Cable(s) Length column represent those customer
selections from Table III of the XYR 6000 Model Selection Guides.
2. In the Cable(s) Length column, entries of the form "X+X" indicate that there are two cables between the
XYR 6000 and the remote antenna, with a lightning surge arrestor used to connect the two cables together.
Entries of the form "X" mean that there is a single cable and that no lightning surge arrestor is used. For
entries of the form "X+X"; the first value is the length of the cable between the instrument and the arrestor
while the second value is the length of the cable between the arrestor and the remote antenna. All cables
are 400 series types as specified in
3. TX Power is set by the Honeywell factory producing the XYR 6000. The factory set value for TX power
is determined by the customer's model number selections in the Model Selection Guide Table III for
antenna type, cables and the lightning suppressor along with the customer's selection in Table V for
Country Code and is consistent with the values shown in
cable lengths, antenna type or the use of a lightning surge arrestor are changed in the field away from the
Model Number listed on the instrument's nameplate, then the TX power setting should likewise be
changed per the tables above to match the new Country/antenna/cable/arrestor selections.
See Section 8.
Japan
4. restricts the TX Power setting to 10 dBm (equivalent to 7 dbm/MHz). N/A entries in this column
mean that these antenna and cable length combinations are not permitted for Japanese applications as using
them would exceed the maximum EIRP values given in
5. The TX Power Setting values given in
circuit within the RF Module. These TX Power Setting values do not include antenna gain nor do they
include the losses caused by cables, connectors and lightning arrestors. When these external gains and
losses are included, then using the TX power values in
EIRP will not exceed the maximum EIRP limits that are given in
6. The TX Power Setting values given in
dBi sectional antenna shown in
7. Units with Model Selection Guide Table III selection A 0 0 0 0 are shipped without cables or a remote
antenna. The Professional Installer must set the TX power for these units according to the characteristics
of the antenna and cables selected by the end user, guided by the information provided above. Only
Omnidirectional antennas with gains less than or equal to 8 dBi and Directional antennas with gains equal
to or less than 14 dBi may be used and still meet Agency restrictions. The TX values used must result in
an EIRP value that does not exceed the maximum EIRP values given in
Honeywell recommends that, regardless of the antenna and cables used, that TX power not be set higher
than 16 dBm in order to maximize the battery life of the instrument.
8. Anatel approvals for Brazil do not permit the use of Honeywell supplied antennas of greater than 6 dBi
gain. Other Anatel approved antennas can be used in Brazil, consult local suppliers for availability.
When using non-Honeywell supplied antennas, adjust TX Power such that the EIRP limit given in Table 7-
2 is not exceeded.
24 OneWireless XYR 6000 Transmitter Professional Installation Guide
Table 5-1 and Table 5-2.
Table
Table 7-3 and Table 7-4
Table 7-3
Table 7-4 for the 14 dBi directional antenna are also used for the 14
Table 6-1. This sectional antenna is only approved for use in Japan.
Table 7-3 and Table 7-4. If the Country location,
7-2.
represent the power produced by the Radio
and Table 7-4 ensures that the XYR 6000
Table 7-1 and Table 7-2
Table 7-1 and Table 7-2.
Revision 3
September 2012