Charging/Recharging The Spotlight - Black & Decker 3 MILLION Power Series User Manual

Twin-beam spotlight

Hide thumbs Also See for 3 MILLION Power Series:

User manual (6 pages)

Manual (6 pages)

Table of Contents

Available languages

R R U U B B B B E E R R B B E E Z Z E E L L

2 2 L L E E D D

A A R R E E A A

L L I I G G H H T T S S

T T W W I I N N H H A A L L O O G G E E N N B B U U L L B B S S

1 1 2 2 V V O O L L T T D D C C

A A C C C C E E S S S S O O R R Y Y O O U U T T L L E E T T

CHARGING/RECHARGING THE SPOTLIGHT

This unit is shipped in a partially charged state. BEFORE first use, charge the Spotlight

using the 127/220 Volt AC Charger for 20-30 hours or until the green LED Indicator

lights.

To check the battery charge status at any time, press the Battery Status Pushbutton.

The LED Indicators display the level of charge. Three red LEDs indicate a high level

of charge; two, a medium level; and one red LED indicates that the unit should be

charged soon.) The green LED lights to show a fully charged unit.

It is recommended that you charge the Spotlight after each use (or every 2 months

when not in frequent use) until the green LED lights so the unit is always ready when

you need it.

C C h h a a r r g g i i n n g g U U s s i i n n g g t t h h e e 1 1 2 2 7 7 / / 2 2 2 2 0 0 V V o o l l t t A A C C C C h h a a r r g g e e r r

• Charges and recharges using a 127V/220V~50-60Hz AC wall cube charger

included.

• Turn OFF the Area Lights and Spotlight (Light Mode Switch is not set to "AREA" and

the Trigger is not depressed). Disconnect any 12 volt DC appliances from the 12

Volt DC Accessory Outlet.

• Charge until the Battery Status LED Indicator green LED lights (approximately 20-

30 hours). DO NOT CHARGE FOR LONGER THAN 30 HOURS.

• Once recharging is completed, disconnect the adapter from the external charging

source.

• After AC recharging, wait 5 minutes before using the Spotlight.

E E A A S S Y Y G G R R I I P P H H A A N N D D L L E E

T T R R I I G G G G E E R R G G U U A A R R D D

( ( A A N N D D T T R R I I G G G G E E R R ) )

C C A A U U T T I I O O N N

Do not turn on any lights or operate any appliances through the Spotlight's DC

Accessory Outlet when using the 127/220 Volt AC Charger.

C C h h a a r r g g i i n n g g U U s s i i n n g g t t h h e e 1 1 2 2 V V o o l l t t D D C C C C h h a a r r g g i i n n g g A A d d a a p p t t e e r r

Make sure the DC source (jump-starter, battery pack, vehicle accessory outlet, etc.) is

12 volt DC and is able to supply at least one half amp at 12 volt DC for 8 hours.

This means a battery pack should be charged with at least 4 amp hours capacity.

The V V E E C C 1 1 5 5 8 8 B B D D can be simultaneously charged and operated from a 12 volt DC

source. M M a a k k e e s s u u r r e e t t h h e e 1 1 2 2 v v o o l l t t D D C C s s o o u u r r c c e e c c a a n n s s u u p p p p l l y y m m i i n n i i m m u u m m 1 1 5 5 a a m m p p s s

o o f f c c u u r r r r e e n n t t i i f f t t h h e e S S p p o o t t l l i i g g h h t t i i s s t t o o b b e e o o p p e e r r a a t t e e d d w w h h i i l l e e t t h h e e b b a a t t t t e e r r i i e e s s a a r r e e b b e e i i n n g g

c c h h a a r r g g e e d d . .

• Insert the 12 volt DC plug end of the 12 Volt DC Charging/Power Adapter into the

accessory outlet of your vehicle or other 12 volt DC power source.

1 1 2 2 V V O O L L T T D D C C C C H H A A R R G G I I N N G G / / P P O O W W E E R R

A A D D A A P P T T E E R R

( ( I I N N C C L L U U D D E E D D ) )

• Plug the barrel-tip end into the 12 Volt DC Charging/Power Port on the back of the

unit.

• Charge until the Battery Status LED Indicator green LED lights when the Battery

Status Display pushbutton is pressed (approximately 3-4 hours). DO NOT CHARGE

FOR LONGER THAN 4 HOURS.

• Once recharging is completed, disconnect the adapter from the external charging/

power source.

Note:

When using a vehicle's 12 volt DC accessory outlet as a charging source, be aware

that some vehicles require you to turn on the ignition to power the accessory outlet.

W W A A R R N N I I N N G G

N N E E V V E E R R A A T T T T E E M M P P T T T T O O U U S S E E T T H H E E A A C C C C H H A A R R G G E E R R A A N N D D D D C C C C H H A A R R G G I I N N G G P P O O R R T T

S S I I M M U U L L T T A A N N E E O O U U S S L L Y Y . .

O O P P E E R R A A T T I I N N G G I I N N S S T T R R U U C C T T I I O O N N S S

O O p p e e r r a a t t i i n n g g t t h h e e S S p p o o t t l l i i g g h h t t a a n n d d L L E E D D A A r r e e a a L L i i g g h h t t s s

To use the lights, first set the Light Mode Switch to the desired operation – "SINGLE"

Spotlight beam, "TWIN" Spotlight beam or "AREA" for LED Area Lights.

To operate the LED Area Lights, simply slide the switch to select AREA. To turn the LED

Area Lights OFF , slide the switch to any other setting.

To operate the Spotlight:

1. Slide the switch to select SINGLE or TWIN beam.

2. Flip up the Trigger Guard (see diagram on page 2).

3. Squeeze the Trigger.

To turn the Spotlight OFF , release the Trigger.