Makita 9561CR Instruction Manual page 8

Switch action (Fig. 2)
CAUTION:
Before!plugging!in!the!tool,!always!check!to!see!that!
the!slide!switch!actuates!properly!and!returns!to!the!
#OFF"!position!when!the!rear!of!the!slide!switch!is!
depressed.
To!start!the!tool,!slide!the!slide!switch!toward!the!#I!(ON)"!
position.!For!continuous!operation,!press!the!front!of!the!
slide!switch!to!lock!it.
To!stop!the!tool,!press!the!rear!of!the!slide!switch,!then!
slide!it!toward!the!#O!(OFF)"!position.
Indication lamp
For Models 9561CVR, 9562CVR, 9564CVR, 9565CVR
(Fig. 3)
For Models 9561CR, 9562CR, 9564CR, 9565CR (Fig. 4)
The!indication!lamp!lights!up!green!when!the!tool!is!
plugged.!If!the!indication!lamp!does!not!light!up,!the!mains!
cord!or!the!controller!may!be!defective.!The!indication!
lamp!is!lit!but!the!tool!does!not!start!even!if!the!tool!is!
switched!on,!the!carbon!brushes!may!be!worn!out,!or!the!
controller,!the!motor!or!the!ON/OFF!switch!may!be!
defective.
Unintentional restart proof
The!tool!does!not!start!with!the!switch!being!lock-on!even!
when!the!tool!is!plugged.
At!this!time,!the!indication!lamp!flickers!red!and!shows!the!
unintentional!restart!proof!device!is!on!function.
To!cancel!the!unintentional!restart!proof,!return!the!slide!
switch!to!#O!(OFF)"!position,!then!release!it.
Speed adjusting dial
For 9561CVR, 9562CVR, 9564CVR, 9565CVR (Fig. 5)
The!rotating!speed!can!be!changed!by!turning!the!speed!
adjusting!dial!to!a!given!number!setting!from!1!to!5.
Higher!speed!is!obtained!when!the!dial!is!turned!in!the!
direction!of!number!5.!And!lower!speed!is!obtained!when!
it!is!turned!in!the!direction!of!number!1.
Refer!to!the!below!table!for!the!relationship!between!the!
number!settings!on!the!dial!and!the!approximate!rotating!
speed.
Number
1
2
3
4
5
010478
CAUTION:
If!the!tool!is!operated!continuously!at!low!speeds!for!a!
long!time,!the!motor!will!get!overloaded!and!heated!up.
The!speed!adjusting!dial!can!be!turned!only!as!far!as!5!
and!back!to!1.!Do!not!force!it!past!5!or!1,!or!the!speed!
adjusting!function!may!no!longer!work.
The!tools!equipped!with!electronic!function!are!easy!to!
operate!because!of!the!following!features.
8
-1
min !(R.P.M.)
2,800
4,000
6,500
9,000
12,000
Electronic!constant!speed!control
Possible!to!get!fine!finish,!because!the!rotating!speed!
is!kept!constantly!even!under!the!loaded!condition.
Soft!start!feature
Soft!start!because!of!suppressed!starting!shock.
Overload!protector
When!the!load!on!the!tool!exceeds!admissible!levels,!
power!to!the!motor!is!reduced!to!protect!the!motor!from!
overheating.!When!the!load!returns!to!admissible!
levels,!the!tool!will!operate!as!normal.
ASSEMBLY
CAUTION:
Always!be!sure!that!the!tool!is!switched!off!and!
unplugged!before!carrying!out!any!work!on!the!tool.
Installing side grip (handle) (Fig. 6)
CAUTION:
Always!be!sure!that!the!side!grip!is!installed!securely!
before!operation.
Screw!the!side!grip!securely!on!the!position!of!the!tool!as!
shown!in!the!figure.
Installing or removing wheel guard (For
depressed center wheel, multi disc/
abrasive cut-off wheel, diamond wheel)
For tool with locking screw type wheel guard (Fig. 7)
CAUTION:
The!wheel!guard!must!be!fitted!on!the!tool!so!that!the!
closed!side!of!the!guard!always!points!toward!the!
operator.
Mount!the!wheel!guard!with!the!protrusion!on!the!wheel!
guard!band!aligned!with!the!notch!on!the!bearing!box.!
Then!rotate!the!wheel!guard!around!180!degrees!
counterclockwise.!Be!sure!to!tighten!the!screw!securely.
To!remove!wheel!guard,!follow!the!installation!procedure!
in!reverse.
For tool with clamp lever type wheel guard (Fig. 8 & 9)
Pull!the!lever!in!the!direction!of!the!arrow!after!loosening!
the!screw.!Mount!the!wheel!guard!with!the!protrusion!on!
the!wheel!guard!band!aligned!with!the!notch!on!the!
bearing!box.!Then!rotate!the!wheel!guard!around!180°.
Fasten!it!with!the!screw!after!pulling!lever!in!the!direction!
of!the!arrow!for!the!working!purpose.!The!setting!angle!of!
the!wheel!guard!can!be!adjusted!with!the!lever.
To!remove!wheel!guard,!follow!the!installation!procedure!
in!reverse.
Installing or removing depressed center
grinding wheel/Multi-disc (accessory)
(Fig. 10)
Mount!the!inner!flange!onto!the!spindle.!Fit!the!wheel/disc!
on!the!inner!flange!and!screw!the!lock!nut!onto!the!
spindle.
To!tighten!the!lock!nut,!press!the!shaft!lock!firmly!so!that!
the!spindle!cannot!revolve,!then!use!the!lock!nut!wrench
and!securely!tighten!clockwise.!(Fig. 11)
To!remove!the!wheel,!follow!the!installation!procedure!in!
reverse.