Optional Accessories - Makita LS0714 Instruction Manual

Replacing fluorescent tube
For model LS0714F, LS0714FL
► Fig.64: 1. Pull out 2. Push 3. Lamp box 4. Screws
5. Fluorescent tube
CAUTION:
• Always be sure that the tool is switched off and
unplugged before replacing the fluorescent
tube.
• Do not apply force, impact or scratch to a flu-
orescent tube, which can cause a glass of the
fluorescent tube to be broken resulting in a
injury to you or your bystanders.
• Leave the fluorescent tube for a while immedi-
ately after a use of it and then replace it. If not.
You may burn yourself.
Remove screws, which secure Lamp Box for the light.
Pull out the Lamp Box keeping pushing lightly the upper
position of it as illustrated on the left.
Pull out the fluorescent tube and then replace it with
Makita original new one.
Cleaning of the lens for the laser
light
For model LS0714FL, LS0714L
► Fig.65: 1. Screwdriver 2. Screw (one piece only)
3. Lens for the laser light
If the lens for the laser light becomes dirty, or sawdust
adheres to it in such a way that the laser line is no
longer easily visible, unplug the saw and remove and
clean the lens for the laser light carefully with a damp,
soft cloth. Do not use solvents or any petroleum-based
cleaners on the lens.
► Fig.66: 1. Lens for the laser light
To remove the lens for the laser light, remove the saw
blade before removing the lens according to the instruc-
tions in the section titled "Installing or removing saw
blade".
Loosen but do not remove the screw which secures the
lens using a screwdriver.
Pull out the lens as shown in the figure.
NOTE:
• If the lens does not come out, loosen the screw
further and pull out the lens again without
removing the screw.
Replacing carbon brushes
► Fig.67: 1. Limit mark
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps.
Take out the worn carbon brushes, insert the new ones
and secure the brush holder caps.
► Fig.68: 1. Brush holder cap 2. Screwdriver
After use
• After use, wipe off chips and dust adhering to the
tool with a cloth or the like. Keep the blade guard
clean according to the directions in the previously
covered section titled "Blade guard". Lubricate the
sliding portions with machine oil to prevent rust.
• When storing the tool, pull the carriage toward you
fully so that the slide pole is thoroughly inserted
into the turn base.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
OPTIONAL
ACCESSORIES
WARNING:
attachments are recommended for use with your
Makita tool specified in this manual. The use of
any other accessories or attachments may result in
serious personal injury.
WARNING:
or attachment for its stated purpose. Misuse of
an accessory or attachment may result in serious
personal injury.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
• Carbide-tipped saw blades
(Refer to our website or contact your local Makita
dealer for the correct saw blades to be used for
the material to be cut.)
• Vise assembly (Horizontal vise)
• Vertical vise
• Holder set
• Holder assembly
• Holder rod assembly
• Set plate
• Dust bag
• Triangular rule
• Fluorescent tube
• Hex wrench
NOTE:
• Some items in the list may be included in the
tool package as standard accessories. They
may differ from country to country.
25 ENGLISH
These Makita accessories or
Only use the Makita accessory