Page 2
The machine owner MUST maintain the original label location and readability. If a label is removed or becomes unreadable, REPLACE the label before using the machine. For new labels, contact Grizzly Industrial Inc. at (570) 546-9663 or techsupport@grizzly.com.
Exhaust Filters ... 20 SECTION 6: SERVICE ... 21 About Service ... 21 Troubleshooting ... 21 G0533 Wiring Diagram ... 22 Parts Breakdown ... 23 Parts List ... 24 Safety Label Placement and Parts List ... 25 WARRANTY AND RETURNS ... 26...
INTRODUCTION Foreword We are proud to offer the Model G0533 3HP Dry Spray Booth. This machine is part of a grow- ing Grizzly family of fine machinery. When used according to the guidelines set forth in this manu- al, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to...
Wear protective hair covering to con- tain long hair and wear non-slip footwear. 6. NEVER OPERATE MACHINERY WHEN TIRED, OR UNDER THE INFLUENCE OF OPERATING DRUGS OR ALCOHOL. Be mentally alert at all times when running machinery. OPERATING MACHINERY. G0533 3HP Dry Spray Booth...
Page 9
16. MAKE SURE GUARDS ARE IN PLACE AND WORK CORRECTLY BEFORE USING MACHINERY. G0533 3HP Dry Spray Booth 17. REMOVE WRENCHES. Make a habit of checking for keys and adjusting wrenches before turn- ing machinery ON.
NFPA 33 and NEC 2005. It is the customer's responsibility to install wiring and a switch in the G0533. Because of the fire/ explosion hazard potential of spray booths, you MUST have a qualified electrician connect the...
Switch and Wiring ...(As per NFPA 33 and NEC regulations) Unpacking (491.7 The Model G0533 was carefully packed when it left our warehouse. If you discover the machine is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice.
• Tap Screws M4 x 45 (Manometer) ... 2 • Red Gauge Oil (Manometer) ... 1 • Arrow Labels (Red and Green) ... 2 G0533 3HP Dry Spray Booth Figure 2. G0533 Inventory. In the event that any nonproprietary parts are missing (e.g.
Lock all entrances to the shop when you are away and DO NOT allow unsupervised children or visitors in your shop at any time! G0533 3HP Dry Spray Booth Exhaust Fan Components and Hardware Needed: Exhaust Fan Housing ...1 Hex Bolts ⁄...
Figure 9. Inserting connector bar. Insert the sockets on the top curtain into the connector bars as shown in Figure 10. G0533 3HP Dry Spray Booth Figure 10. Top curtain attached to connector Components and Hardware Needed: Work Table ...1...
Figure 14. First stage filters. Outer Rail The G0533 dry spray booth must be vented to the outside of your shop or building using 12" metal spiral wound ducting or 18 gauge rolled galvanized steel ducts in accordance with NFPA 33 guidelines.
Install a tubing connector fitting in the larger pre-drilled hole on the side of the booth near the manometer as shown in Figure 16. G0533 3HP Dry Spray Booth Figure 16. Tubing installed onto spray booth Run tubing from the low pressure side (-) of the manometer to the tubing connector fitting as shown in Figure 16.
OMMEND that you read books, trade maga- zines, or get formal training before begin- ning any projects. Regardless of the con- tent in this section, Grizzly Industrial will not be held liable for accidents caused by lack of training, neglect or misuse.
Page 21
New Filter Indicator Mark Figure 19. New filter installation mark example. G0533 3HP Dry Spray Booth Multiply the reading from Step 6 times 2 (2x) and mark with the supplied red arrow (Figure 20). This is the dirty filter indicator mark.
Disposal varies depending on the type of paint being captured. Consult local authorities for storage and disposal recommen- dations. G0533 3HP Dry Spray Booth red gauge oil. ®...
Spray Booth Operations SYMPTOM Too little airflow in booth. Too much airflow in booth. The filter indicator does not work prop- erly. G0533 3HP Dry Spray Booth About Service Troubleshooting POSSIBLE CAUSE 1. Paint build-up on exhaust fan blades or exhaust duct.
TOP STEEL CURTAIN SMALL TOP CURTAIN TAP SCREW 1/4 x 1/2 FLAT WASHER 1/4 HEX NUT 1/4-20 10 MICRON SECOND STAGE FILTER 30 MICRON FIRST STAGE FILTER RIGHT STEEL CURTAIN SUPPPORT BAR OUTLET GASKET INLET GASKET G0533 3HP Dry Spray Booth...
The machine owner MUST maintain the original label location and readability. If a label is removed or becomes unreadable, REPLACE the label before using the machine. For new labels, contact Grizzly Industrial Inc. at (570) 546-9663 or PART #...
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
Page 29
Do you think your machine represents a good value? Would you recommend Grizzly Industrial to a friend? Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We never use names more than 3 times.
Page 30
FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 Name_______________________________ Street_______________________________ City______________State______Zip______ TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...
Page 32
Buy Direct and Save with Grizzly Visit Our Website Today And Discover Why • • • – Trusted, Proven and a Great Value! ® Grizzly Is The Industry Leader! ® SECURE ORDERING ORDERS SHIPPED WITHIN 24 HOURS E-MAIL RESPONSE WITHIN ONE HOUR...