Grizzly H7673 Instruction Manual
  1. Manuals
  2. Brands
  3. Grizzly Manuals
  4. Paint Sprayer
  5. H7673
  6. Instruction manual

Grizzly H7673 Instruction Manual

Deluxe mini hvlp spray gun
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
DELUXE MINI HVLP SPRAY GUN
MODEL H7673
INSTRUCTION MANUAL
COPYRIGHT © JUNE, 2005 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#PC7347 PRINTED IN CHINA

Advertisement

Table of Contents
loading

Related Manuals for Grizzly H7673

Summary of Contents for Grizzly H7673

  • Page 1 DELUXE MINI HVLP SPRAY GUN MODEL H7673 INSTRUCTION MANUAL COPYRIGHT © JUNE, 2005 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #PC7347 PRINTED IN CHINA...

  • Page 3: Table Of Contents

    Inventory ...8 Assembly ...9 Controls ...9 SECTION 4: OPERATIONS ...10 Spraying ...10 Atomizing Cap and Fan Adjustments ...12 SECTION 5: MAINTENANCE ...13 Cleaning ...13 Lubrication ...14 Troubleshooting ...15 Parts Breakdown ...17 WARRANTY AND RETURNS ...18 Model H7673 HVLP Spray Gun...

  • Page 4: Section 1: Safety

    USE THE RIGHT TOOL. Do not force tool or attachment to do a job for which it was not designed. INFLUENCE ALCOHOL. Model H7673 HVLP Spray Gun WORKSHOP CHILD UNDER DRUGS...

  • Page 5: Safety Instructions For Pneumatic Tools

    17. REDUCE UNINTENTIONAL STARTING. Do not carry tool with hand on trig- ger and always disconnect from air when not in use. Model H7673 HVLP Spray Gun 18. DISCONNECT TOOLS before ser- vicing and changing accessories. 19. USE ACCESSORIES. owner’s manual for recommended accessories.

  • Page 6: Additional Safety Instructions For Hvlp Spray Guns

    NOT exceed the recommended inlet air pressure. Excessive pres- sure could cause the spray gun to burst or cause other internal equip- ment damage. 14. LOCAL authorities regarding exhaust and waste disposal requirements. PRESSURE. LAWS. Consult Model H7673 HVLP Spray Gun local...

  • Page 7: Section 2: Introduction

    Grizzly’s commit- ment to customer satisfaction. The Model H7673 is designed to be used for smaller jobs where large volumes of material are not needed. The Model H7673 features HVLP technology, which...

  • Page 8: Section 3: Set Up

    Inventory After you have unpacked the carton you should find the following: Model H7673 Inventory (Figure 1) A. Spray Gun ..1 B. Cup 100 ml ... 1 C. Cleaning Brush ... 1 D. Service Wrench ... 1 E.

  • Page 9: Assembly

    If you need additional help with this assem- bly, call our Technical Support at: (570) 546-9663. Model H7673 HVLP Spray Gun Controls Atomizing Cap Trigger Pattern Control Air Flow Control Figure 3.

  • Page 10: Section 4: Operations

    Spraying The Model H7673 HVLP spray gun is designed to spray low to medium solid materials, like lacquers, stains, primers, multi-component paints, acrylics, epoxies etc.
  • Page 11 Model H7673 HVLP Spray Gun 10. Begin spraying 2-3 inches before the work and continue to the end of the work. Continue the motion for a few inches past the work until you are ready for the return stroke.

  • Page 12: Atomizing Cap And Fan Adjustments

    Figure 7. Set up for vertical spray stroke with horizontal fan pattern. Rotating the pattern adjustment control in Figure 7 will give you a range between the two patterns in Figure 8. 190 mm Figure 8. Fan adjustment. Model H7673 HVLP Spray Gun Pattern Control...

  • Page 13: Section 5: Maintenance

    Strainer Atomizing Spring & Needle Figure 9. Disassembly for cleaning. Model H7673 HVLP Spray Gun 5. Unscrew the atomizing cap with your fingers and the fluid tip with the ser- vice wrench. The fully disassembled gun should look like Figure 9.

  • Page 14: Lubrication

    B. Air Valve Packing C. Trigger Pin D. Air Flow Control Valve E. Pattern Control F. Fluid Control Knob After each cleaning apply a thin film of petroleum jelly to the needle spring before reassembling. Model H7673 HVLP Spray Gun...

  • Page 15: Troubleshooting

    No spray output. 1. No pressure at gun. 2. Fluid passages dirty. 3. Fluid control closed. 4. Out of paint. Model H7673 HVLP Spray Gun Troubleshooting Solution 1. Tighten fluid tip or replace seat with new one. 2. Add material.
  • Page 16 1. Lower inlet air pressure. 2. Keep gun at recommended distance. 3. Slow down and maintain consistent even parallel stroke. 1. Clean or replace both. 1. Install an in-line air filter. 2. Replace air line. Model H7673 HVLP Spray Gun...

  • Page 17: Parts Breakdown

    PH7673017 FLUID NOZZLE WASHER PH7673018 NOZZLE BOLT PH7673019 COMPRESSED SPRING PH7673020 NEEDLE WASHER PH7673021 TRIGGER LEVER 1 PH7673022 TRIGGER LEVER 2 Model H7673 HVLP Spray Gun Parts Breakdown �� �� �� �� �� �� �� �� �� �� � �...

  • Page 18: Warranty And Returns

    WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
  • Page 19 ____20-29 ____50-59 How long have you been a woodworker/metalworker? ____0-2 Years How many of your machines or tools are Grizzly? ____0-2 Do you think your machine represents a good value? ____Yes Would you recommend Grizzly Industrial to a friend? ____Yes Would you allow us to use your name as a reference for our customers in your area? Note: We never use names more than 3 times.
  • Page 20 Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...

Table of Contents