Cables And Flexible Leaders; Tools And Replacement Blades; Machine Assembly; Instructions For Installing Handle - RIDGID 60062R Manual

• K-7500 Machine with AUTOFEED, toolbox, stan-
dard tools and C-24 Cable (

Cables and Flexible Leaders

Catalog
No.
92460
92465
92470
" (16mm)
5 /
8
43647
32737
58192
" (16mm)
5 /
8
95762
95757
95752
" (16mm)
5 /
8 95747
92475
92480
41212
" (20mm)
3 /
41697
4
47427
47432
" (20mm)
3 /
4
92555
92560
44122
44117
Tools and Replacement Blades — Fits C-24,
C-25, C-26, C-27,C-28, C-29, C-75, C-100,
C-24HC, C-27HC, C-75HC and C-100HC
Catalog
No.
92485
92490
92495
92500
92505
51762
92510
92515
92520
92525
92530
92535
92540
92545
92550
1.800.561.8187
" x 100' Inner-Core)
5 /
8
Model
No. Description
25' I.C. Cable (7,6m)
C-25
50' I.C. Cable (15,2m)
C-26
75' I.C. Cable (22,9m)
C-27
100' I.C. Cable (30,5m)
C-24
75' Hollow-Core (22,9m)
C-27HC
100' Hollow-Core (30,5m)
C-24HC
25' I.W. Cable (7,6m)
C-25 IW
50' I.W. Cable (15,2m)
C-26 IW
75' I.W. Cable (22,9m)
C-27 IW
100' I.W. Cable (30,5m)
C-24 IW
C-28 25' I.C. Cable (7,6m)
C-29 50' I.C. Cable (15,2m)
C-75 75' I.C. Cable (22,9m)
C-100 100' I.C. Cable (30,5m)
C-75HC 75' Hollow-Core (22,9m)
C-100HC 100' Hollow-Core (30,5m)
" x 2' Leader
T-458 5 /
8
" x 2' Leader
T-468 3 /
4
" Pigtail
5 /
—
8
" Pigtail
3 /
—
4
Replacement
Model
No. Description Blade(s)
T-403 P-Trap Cutter, 3" 92835
"
T-404 P-Trap Cutter, 3 1 / 92840
2
T-406 Spear Blade 92850
T-407 Retrieving Auger —
T-408 Sawtooth Cutter 92890
H-D Bulb Auger —
T-409
Double Cutter, 2" 92815
T-411
"
T-412 Double Cutter, 2 1 / 92820
2
T-413 Double Cutter, 3" 92825
T-414 Double Cutter, 4" 92830
T-416 Double Cutter, 6" 92855
T-432 3-Blade Cutter, 2" 92860
T-433 3-Blade Cutter, 3" 92865
T-434 3-Blade Cutter, 4" 92870
T-436 3-Blade Cutter, 6" 92875
www.
K-7500 Drain Cleaning machine
Blade
Holder
Coupling*
Figure 2 – Tool Assembly

Machine Assembly

To prevent serious injury, proper assembly of the
Drain Cleaner is required. The following procedures
should be followed:

Instructions for Installing Handle

Raise the stair climber to the upper position by pulling out
Holder*
the locking pin and lifting the stair climber by the cross
92900
member until the pin locks into the upper position (Figure
92900
3). Insert handle through the motor table rail supports and
92915
through the two holes on rear support (Figure 4) . Insert the
— two hairpin cotter fasteners through the holes in the bot-
tom of the handle (Figure 5) . Adjust handle to desired
92915
height. Securely tighten the two T-shaped mounting
knobs on rear support. Lower the stair climber.
—
92905
92905
92910
92910
92910
92895
92895
92895
92895
Figure 3 – Raising Stair Climbers
.com
Blade
* Identifies components
included with holder
WARNING
information@itm.com
Fastener*
5