Makita DDF484 Instruction Manual
Hide thumbs
Also See for DDF484:
- Instruction manual (65 pages) ,
- Instruction manual (13 pages) ,
- Instruction manual (15 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita DDF484
Summary of Contents for Makita DDF484
- Page 1 INSTRUCTION MANUAL Cordless Driver Drill DDF484 Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: DDF484 Drilling capacities Steel 13 mm Wood 38 mm Fastening capacities Wood screw 10 mm x 90 mm Machine screw No load speed High (2) 0 - 2,000 min Low (1) 0 - 500 min Overall length 172 mm Rated voltage D.C. -
Page 3: General Power Tool Safety Warnings
Prevent unintentional starting. Ensure the SAFETY WARNINGS switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with General power tool safety warnings your finger on the switch or energising power tools that have the switch on invites accidents. WARNING: Remove any adjusting key or wrench before Read all safety warnings and... - Page 4 DO NOT let comfort or familiarity causing fires, personal injury and damage. It will with product (gained from repeated use) replace also void the Makita warranty for the Makita tool and strict adherence to safety rules for the subject charger. product. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury.
-
Page 5: Functional Description
Tips for maintaining maximum CAUTION: Always install the battery cartridge battery life fully until the red indicator cannot be seen. If not, it may accidentally fall out of the tool, causing injury to Charge the battery cartridge before completely you or someone around you. discharged. Always stop tool operation and charge the battery cartridge when you notice CAUTION: Do not install the battery cartridge... -
Page 6: Overload Protection
Tool / battery protection system CAUTION: Before installing the battery car- tridge into the tool, always check to see that the The tool is equipped with a tool/battery protection sys- switch trigger actuates properly and returns to tem. This system automatically cuts off power to the the "OFF" position when released. motor to extend tool and battery life. The tool will auto- matically stop during operation if the tool or battery is To start the tool, simply pull the switch trigger. Tool placed under one of the following conditions: speed is increased by increasing pressure on the switch... -
Page 7: Speed Change
CAUTION: CAUTION: Always check the direction of Always set the speed change lever rotation before operation. fully to the correct position. If you operate the tool with the speed change lever positioned halfway CAUTION: Use the reversing switch only after between the "1" side and "2" side, the tool may be the tool comes to a complete stop. -
Page 8: Installing Hook
Graduation Machine screw Wood Soft wood – ɸ3.5 x 22 ɸ4.1x 38 – screw (e.g. pine) Hard wood – ɸ3.5 x 22 ɸ4.1x 38 – (e.g. lauan) Installing driver bit holder ASSEMBLY Optional accessory CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. -
Page 9: Drilling Operation
CAUTION: hammer at the point to be drilled. Place the point of the These accessories or attachments drill bit in the indentation and start drilling. are recommended for use with your Makita tool Use a cutting lubricant when drilling metals. The excep- specified in this manual. The use of any other tions are iron and brass which should be drilled dry. accessories or attachments might present a risk of injury to persons. Only use accessory or attachment... - Page 12 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885510-222 www.makita.com 20160422...