Table of Contents
Advertisement
Quick Links
Installation Instructions
®
Zenith HydroTap
®
Filtered Chilled drinking water for commercial kitchens and tea rooms.
The G4 applaince series offers a range of interchangeable taps to suit the customer's needs
Chilled Commercial
Affix Model Number Label
Here
801525NZ
801525NZ - Chilled HydroTap Installation Instructions - Aug 2015 - v2.00
Page 1 of 20
Advertisement
Table of Contents
Related Manuals for Zenith HydroTap C125
Summary of Contents for Zenith HydroTap C125
-
Page 1: Step
Installation Instructions ® Zenith HydroTap ® Filtered Chilled drinking water for commercial kitchens and tea rooms. The G4 applaince series offers a range of interchangeable taps to suit the customer’s needs Chilled Commercial Affix Model Number Label Here 801525NZ 801525NZ - Chilled HydroTap Installation Instructions - Aug 2015 - v2.00... -
Page 2: Step
Notes Page 2 of 20 801525NZ - Chilled HydroTap Installation Instructions - Aug 2015 - v2.00... -
Page 3: Table Of Contents
Index HydroTap Specifications Installation check list ........................4 General Product Features ......................5 Important Safety Instructions ....................... 6 Warnings and Regulatory Information ..................7 Major components and Accessories .................... 7 Technical Specification ........................ 8 Before installation and site requirements ..................8 Installation Instructions STEP 1 - Measure and cut all the tap holes before fitting the taps... -
Page 4: Installation Checklist
Installation checklist Before Installation: Read the instructions and check if there is adequate space to mount all of the components. Note: Not all fittings are supplied with the appliance kit. Isolation valves are not supplied. Check the mains water pressure is between 172 - 700kPa Check the water quality to determine if extra filtration will be required. -
Page 5: General Product Features
General Product Features Thank you for purchasing a Zenith Chilled HydroTap. Please read and follow these instructions carefully to ensure safe operation and trouble free service. If service is required, please call 0800 558055 What is the Zenith HydroTap ? The Chilled Zenith HydroTaps are electronically controlled to supply filtered and Chilled drinking water for kitchens and tea rooms. -
Page 6: Important Safety Instructions
Lifting Take care when lifting the Zenith HydroTap unit. Some units may exceed safe lifting limits. If you feel this is beyond your personal capabilities, please seek assistance with the lift. The weights of the units are marked on the packaging. -
Page 7: Warnings And Regulatory Information
Major components and accessories Parts supplied Description Accessories Description HydroTap Font Kit for with hoses Arc & Cube Models (Classic tap shown) 1 off Font Kit for Classic & HydroTap Elite Models Undersink Unit with water filter 1 off Mains water connection hose Replacement Filter 1 x Kickboard louvre... -
Page 8: Technical Specification
Technical Specifications Before installing ensure that the following have been provided at the installation site: • Review all the technical specifications. • Ensure the underbench can support the product weight when full of water, (allow an extra 3 kg when full. ) •... -
Page 9: Measure And Cut All The Tap Holes Before Fitting The Taps Section 1 - Tap Installation Instructions 1.1 - Hydrotap Tap Installation
Position the tap such that it dispenses into the sink bowl with ample clearance for a cup or tea pot. Alternatively, the tap could be mounted away from the sink using a Zenith Font, available as an accessory. Recommended dispensing distance... - Page 10 HydroTap & Elite Installation EliteTap HydroTap Classic ALL THREAD STAINLESS STEEL BLACK PLASTIC SPACER SPACER SPIDER CLAMP Tap assembly exploded view and kitchen layout side view. BENCH TOP Ø35mm Apply a light smearing of silicon sealant on the underside of the spacer to ensure a watertight fit. Cut a 35mm hole in the bench / sink top.
-
Page 11: Installation Instructions
Installation Instructions BLACK PLASTIC STAINLESS SPACER STEEL WASHER Fit the STAINLESS STEEL WASHER, SPIDER CLAMP SPIDER CLAMP, AND 6mm NUT. 6mm NUT 35mm hole Note feed each of the three tubes and electrical cable evenly in between the legs of Pass all the hoses, tubes and USB lead the SPIDER CLAMP when installing. - Page 12 HydroTap Arc/Cube The HydroTap Arc/Cube has a spout that may be fixed in one of 6 angular positions (depending on the position of the rotary control) and fixed in one of two height positions. The spout is fixed and does not swivel. NOTE: The tube kit must be fitted after the HydroTap has been mounted on the benchtop or sink.
- Page 13 Installation Instructions Height adjustment (Fixed position options) 50mm Angular adjustment (Fixed position options) Left Hand Control Right Hand Control NOTE: Position A is not recommended with Boiling water units Mounting (See table on Page 11 ) O-RING BENCH TOP LOWER Ø35mm RUBBER WASHER...
-
Page 14: Section 2 - Ventilation
Section 2 Ventilation When installing air flow ducts, the following tools will be required: • Jigsaw and 12mm drill. • Keyhole or Wall Board saw. Recommended Installation showing the correct air flow MIN. 35mm Cool Air IN **MIN. via cabinet 100mm Warm Air OUT floor, front... - Page 15 Ventilation Min. 35mm The following instructions are critical if the vent kit, as supplied, is not fitted: If the kick board vent kit cannot be used then it is important to fit a standard HydroTap vent kit, which ensures heat dissipation through natural convection via installed vents. For high use applications, where the cupboard space temperature is near 35°C, or higher, an auxillary ventilation kit must be fitted.
-
Page 16: Section 3 - Undersink Unit Installation
Section 3 Undersink Unit Installation Hose and tube fitting. (Do not overtighten) • Remove all caps from the top of the undersink unit. • Fit the foam insulation to the Blue tube after trimming to length. • Install the mains water braided hoses to the undersink unit before locating the unit in place. BLUE BRAIDED Model C125... -
Page 17: Section 4 - Commissioning
Section 4 Commissioning • Turn ON the water and check for any leaks. • Turn the power ON at the GPO • Familiarise yourself with the operation of the Tap, in preparation for use (See User Guide) • Follow the Installation instructions below (and review Section C of the User Guide). •... -
Page 18: Flow Calibration
Commissioning Flow Calibration Press the [Start] button and the tank will first empty then fill. This will take aprox 5 minutes. Upon completion the actual pulse will be displayed. Press [Next] for the Boiling Calibration screen. Page 18 of 20 801525NZ - Chilled HydroTap Installation Instructions - Aug 2015 - v2.00... -
Page 19: Trouble Shooting
Internal fault Call Zenith Service Call an electrician, a plumber, or Zenith on 0800 558055 for assistance, service, spare parts or enquiries. End of Life Disposal In order to help preserve our environment we ask that you dispose of this product correctly. Please contact your local city council for collection centre details. -
Page 20: Contact Details
WMKA00099 AS 3498 The standard glass is 200 ml (7 fl oz). The terms “Zenith” and “HydroTap” are registered trade marks of Zip Heaters (Aust) Pty Ltd. Zenith products described in this publication are manufactured under one or more of the following patents: AU675601, AU637412, AU635979, GB0422305, GB2065848, US4354049, US5103859, US5099825 and SA2006/08043.