HIKVISION DS-K1101M Installation Manual
Ds-k1101 series;
ds-k1102 series;
ds-k1103 series
Hide thumbs
Also See for DS-K1101M:
- Installation manual (18 pages) ,
- User manual (24 pages) ,
- Quick start manual (5 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for HIKVISION DS-K1101M
Summary of Contents for HIKVISION DS-K1101M
-
Page 1: Installation Manual
DS-K1100 Series Card Reader Installation Manual UD.6L0206A1003A01... - Page 2 Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact the dealer. This manual is applicable to the following models: Series Models Description DS-K1101M MIFARE card reader (without keypad) DS-K1101MK MIFARE card reader (with a keypad) DS-K1101 Series...
-
Page 3: Chapter 1 Preventive And Cautionary Tips
Chapter 1 Preventive and Cautionary Tips To guarantee the card reader works properly, please read and obey the notes below. If the card reader is powered by the controller, the power supply distance is recommended to be no longer than 100m. If the distance is longer than 100m, you are advised to power the card reader by external 12V (range: -%10 ~ +%10) DC power supply, which is nonswitched and linear. -
Page 4: Front View
2.1 Front View The front view of DS-K1101 series card reader is shown below: Figure 2-1 DS-K1101MK/DS-K1101CK Figure 2-2 DS-K1101M/DS-K1101C The front view of DS-K1102 series card reader is shown below: Figure 2-3 DS-K1102MK/DS-K1102CK Figure 2-4 DS-K1102M/DS-K1102C The front view of DS-K1103 series card reader is shown below:... -
Page 5: Rear View
Figure 2-5 DS-K1103MK/DS-K1103CK Figure 2-6 DS-K1103M/DS-K1103C 2.2 Rear View The rear view of card reader is shown below: Figure 2-7 Rear View of DS-K1101 Series... - Page 6 Figure 2-8 Rear View of DS-K1102 Series Figure 2-9 Rear View of DS-K1103 Series...
-
Page 7: Side View
Table 2-1 Description of Rear View Name Cable Interface of RS-485, Power, LED Control, etc. Buzzer Tamper-proof Module DIP Switch PSAM Card Slot (available for CPU card reader) 2.3 Side View The side view of card reader is shown below: Figure 2-10 Side View of DS-K1101 Series... -
Page 8: Installing Psam Card
Figure 2-11 Side View of DS-K1102 Series Figure 2-12 Side View of DS-K1103 Series Chapter 3 Installation 3.1 Installing PSAM Card PSAM card slot is only available for CPU card reader. Insert the PSAM card into the slot according to the direction... -
Page 9: Introduction For Dip Switch
shown below. Figure 3-1 PSAM Card Slot 3.2 Introduction for DIP Switch The DIP switch module is shown below. The No. of DIP switch from left to right is 1 ~ 8. Figure 3-2 DIP Switch Module Table 3-1 Description of DIP Switch Icon Description Represent 1 in binary mode... -
Page 10: Definition Of Cable
Table 3-2 Description of DIP Switch Description DIP Switch Status 1: 1 1 ~ 4 Address of RS-485 0: 0 Read card No. or file in card. 1: read card No; (Only available for CPU card 0: read file in card. reader.) Wiegand protocol or RS-485 1: Wiegand protocol;... -
Page 11: Wiring Cables
Color Description Orange Red LED Control (available for Wiegand Protocol) PWR (DC +12V) 3.4 Wiring Cables Purpose: Wire the cables between controller and card reader, thus to establish the communication between them. Steps for RS-485 communication mode: Set the DIP switch of No. 6 as 0. Set the DIP switch of No. - Page 12 Controller Card Reader Figure 3-4 Wiring for RS-485 Communication Mode Steps for Wiegand communication mode: Set the DIP switch of No. 6 as 1. Set the DIP switch of No. 5 and 7 for reading card mode and Wiegand protocol. For details, please refer to 3.2 Introduction for DIP Switch.
-
Page 13: Installing Card Reader
Controller Card Reader Figure 3-5 Wiring for Wiegand Communication Mode 3.5 Installing Card Reader Before you start: Set the DIP switch. For details, refer to 3.2 Introduction for DIP Switch. Steps:... -
Page 14: Chapter 4 Sound Prompt And Indicator
Fix the plate on the wall or other place. Connect the cables between controller and card reader. For details, refer to 3.4 Wiring Cables. Push the card reader to match the fixed plate. Fasten the screw to keep the components together. Chapter 4 Sound Prompt and Indicator After the card reader is powered on, LED status indicator will turn blue and blink for 1 time. - Page 15 Table 4-1 Description of Prompt Sound Sound Prompt Description RS-485 protocol: Pressing keys prompt; Swiping card prompt; Time out prompt for One beep pressing keys or swiping card. Wiegand protocol: Pressing keys prompt; Swiping card prompt. The operation of pressing keys or swiping Two rapid beeps card is valid.