Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HIKVISION DS-K1108AM
Summary of Contents for HIKVISION DS-K1108AM
- Page 1 DS-K1107 Series Card Reader User Manual UD05519B...
- Page 2 ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”). This user manual (hereinafter referred to be “the Manual”) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.
- Page 3 DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS.
-
Page 4: Chapter 1 Preventive And Cautionary Tips
Chapter 1 Preventive and Cautionary Tips To guarantee the card reader works properly, please read and obey the notes below. If the card reader is powered by the controller, the power supply distance is recommended to be no longer than 100m. If the distance is longer than 100m, you are advised to power the card reader by external 12V (range: -%10 ~ +%10) DC power supply, which is nonswitched and linear. -
Page 5: Chapter 2 Introduction
Chapter 2 Introduction 2.1 Over View Figure 2-1 DS-K1107 Series Card Reader DS-K1107 series card reader is a kind of high-performance product, with a 32 bit high-speed processor. It communicates with access controller via either RS-485 protocol (AES encrypted) or Wiegand protocol. -
Page 6: Indicator And Component
2.2 Indicator and Component Figure 2-2 2.2 Indicator and Component Chapter 3 Installation 3.1 Introduction for DIP Switch The DIP switch module is shown below. The No. of DIP switch from left to right is 1 ~ 8. - Page 7 Figure 3-1 DIP Switch Module Table 3-1 Description of DIP Switch Icon Description Represent 1 in binary mode Represent 0 in binary mode For example, binary value of the following status is: 0000 1100. Figure 3-2 DIP Switch Module Table 3-2 Description of DIP Switch Description DIP Switch Status 1: 1...
-
Page 8: Definition Of Cable
3.2 Definition of Cable The description of 10 cables is shown below. Table 3-3 Description of Cable Color Description Orange Red LED Control (available for Wiegand Protocol) White Wiegand W1 (available for Wiegand Protocol) Green Wiegand W0 (available for Wiegand Protocol) Green RS-485- Yellow... - Page 9 shown below. Controller Card Reader Card Reader Figure 3-3 Wiring for RS-485 Communication Mode Steps for Wiegand communication mode: Set the DIP switch of No. 6 as 1. Set the DIP switch of No. 7 for reading card mode and Wiegand protocol.
-
Page 10: Installing Card Reader
Controller Card Reader Card Reader Figure 3-4 Wiring for Wiegand Communication Mode 3.4 Installing Card Reader Before you start: Set the DIP switch. For details, refer to 3.1 Introduction for DIP Switch. -
Page 11: Chapter 4 Sound Prompt And Indicator
Installation for DS-K1101/ 02/ 03/ 04 series card reader Steps: 1. Fix the plate on the wall or other places by using two screws (PA4×25-SUS). Make sure the arrows on the plate are upwards. 2. Check whether the plate is fixed and in the right direction. - Page 12 times. At last the buzzer will send out a beep sound indicating the starting up process is completed. When using the card reader, it will send out different sounds prompt and the LED indicator to indicate different statuses. You can refer to tables below for detailed information. Table 1-1 Description of Prompt Sound Sound Prompt Description...
- Page 13 Table 1-2 Description of LED Indicator LED Indicator Status Description Green (blink for 1 time), and red (blink The card reader is power on. for 3 times) For Card + Fingerprint authentication: prompt for pressing the fingerprint after swiping the card. Green and blinking operation configuring...