Fcc Requirements; Dolphin Rf Terminal-802.11A/B/G/N/Ac, Bluetooth, And/Or Gsm; Canadian Compliance, Conformité À La Règlementation Canadienne; Rf Exposure Information (Sar) - Honeywell Dolphin 75e User Manual

Preliminary Draft, Not for Release - Please Review 2-3-2015

FCC Requirements

Dolphin RF Terminal—802.11a/b/g/n/ac, Bluetooth, and/or GSM
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions.
The user may find the following booklet helpful: "Something About Interference." This is available at FCC local regional
offices. Our company is not responsible for any radio or television interference caused by unauthorized modifications of this
equipment or the substitution or attachment of connecting cables and equipment other than those specified by our
company. The correction is the responsibility of the user. Use only shielded data cables with this system.
Canadian Compliance, Conformité à la règlementation canadienne
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
5GHz band: Sub-band 5.150 - 5.250 GHz of the 5GHz LE-LAN (License Exempt Local Area Network Devices) supported in this
device is permitted for indoor operation only.
Cet appareil est conforme aux normes RSS avec exemption de licence d'Industrie Canada. Son fonctionnement est assujetti
aux conditions suivantes:
1. Cet appareil ne doit pas causer de brouillage préjudiciable.
2. Cet appareil doit pouvoir accepter tout brouillage reçu, y compris le brouillage pouvant causer un fonctionnement
indésirable.
Bande 5 Ghz: La bande inferieure de 5,150 à 5,250 GHz de la 5GHz LE-LAN (License Exempt Local Area Network Devices)
pris en charge dans ce dispositif est autorisée pour une utilisation en intérieur uniquement.

RF Exposure Information (SAR)

This device meets the government's requirements for exposure to radio waves. This
exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the
U.S. Government.
The exposure standard for wireless devices employs a unit of measurement known as the Specific Absorption Rate, or SAR.
The SAR limit set by the FCC is 1.6W/Kg and for Europe 2W/Kg. Although the SAR is determined at the highest certified power
level, the actual SAR level of the
designed to operate at multiple power levels so as to use only the poser required to reach the network. In general, the closer you
are to a wireless base station antenna, the lower the power output.
1 - 2
device while operating can be well below the maximum value. This is because the
device is designed and manufactured not to
device is