Eng302 - Makita 8271D Instruction Manual

For Model 8391D
For European countries only
Noise
The typical A-weighted
according to EN60745:
Sound pressure level (L
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
Wear ear protection.
Vibration
The vibration total
determined according to EN60745-2-1:
Work mode: impact drilling into concrete
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : drilling into metal
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The declared vibration emission value has been
•
measured in accordance with the standard test method
and may be used for comparing one tool with another.
The declared vibration emission value may also be
•
used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual use of the power
•
tool can differ from the declared emission value
depending on the ways in which the tool is used.
Be sure to identify safety measures to protect the
•
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
For European countries only
EC Declaration of Conformity
Makita declares that the following Machine(s):
Designation of Machine:
Cordless Hammer Driver Drill
Model No./ Type: 8271D/8281D/8381D/8391D
Conforms to the following European Directives:
2006/42/EC
They are manufactured in accordance with the following
Standard or standardized documents:
EN60745
The Technical file in accordance with 2006/42/EC is
available from:
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
noise level determined
) : 78 dB (A)
pA
value (tri-axial vector
2
) : 8 m/s
h,ID
2
2
) : 2.5 m/s or less
h,D
2
ENG104-1
000331
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
ENG203-1
General Power Tool Safety Warnings
sum)
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for

ENG302-2

future reference.
SPECIFIC SAFETY RULES
ENG901-1
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to hammer drill safety rules. If you use this power
tool unsafely or incorrectly, you can suffer serious
personal injury.
1. Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
2. Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
3. Hold
surfaces, when performing an operation
where the cutting accessory may contact
hidden wiring or its own cord. Cutting
accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
4. Always be sure you have a firm footing.
ENH101-17
Be sure no one is below when using the tool
in high locations.
5. Hold the tool firmly with both hands.
6. Keep hands away from rotating parts.
7. Do not leave the tool running. Operate the tool
only when hand-held.
8. Do not touch the bit or the workpiece
immediately after operation; they may be
extremely hot and could burn your skin.
9. Some material contains chemicals which may
be toxic. Take caution to prevent dust
inhalation and skin contact. Follow material
supplier safety data.
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated in this
instruction manual may cause serious personal injury.
4
31.12.2013
Yasushi Fukaya
Director
power tool by insulated
GEA010-1
GEB003-4
gripping