Configuration Parameters - Honeywell TB7200 Series Installation Instructions Manual

TB7200 SERIES COMMUNICATING ZONE THERMOSTATS
Configuration
parameters
PswrdSet Configuration parameters menu
access password
Default value = 0
Range is: 0 to 1000
Com Addr Thermostat networking address
Default value = 254
Range is: 0 to 254
Personal Area Network
PAN ID
Identification
Default value = 0
Range is: 0 to 500
Channel selection
Channel
Default value = 10
Set to: 15 or 25
Range is: 10 to 26
Get From another thermostat
Get From
configuration utility
Default value = 255
Range is: 0 to 254
62-2019—05
Table 8. Configuration Parameters
Default value Significance and adjustments
This parameter sets a protective access password to prevent
unauthorized access to the configuration menu parameters. A default
value of "0" will not prompt a password or lock the access to the
configuration menu.
If the thermostat is installed as a stand-alone unit, this parameter will
not be used or displayed
For BACnet models valid range to use is from 0 to 127. Default value
of 254 disables BACnet communication for the thermostat.
For wireless models valid range is 0 to 254 with a maximum of 30
thermostats per WEB-2xx controller and 50 thermostats per WEB-
6xx/-7xx controller.
Conditional parameter to wireless models (TB7200X5x14W)
This parameter will only appear on wireless thermostats. If the
thermostat is BACnet, this parameter will not be used or displayed
This parameter (Personal Area Network Identification) is used to link
specific thermostats to a single specific WEBs controller with a
wireless communication card (TB-VWG-APP-1014). For every
thermostat reporting to a WEBs controller and wireless
communication card (maximum of 30 thermostats per WEB-2xx
controller and 50 thermostats per WEB-6xx/-7xx controller) be sure
you set the SAME PAN ID value both at the wireless communication
card and the thermostat(s).
The default value of 0 is NOT a valid PAN ID. The valid range of
available PAN ID is from 1 to 500
Conditional parameter to wireless models (TB7200X5x14W)
This parameter will only appear when a wireless network adapter is
present. If the thermostat is installed as a stand-alone unit or is a
BACnet model, this parameter will not be used or displayed
This parameter (Channel) is used to link specific thermostats to a
specific WEBs controller with a wireless communication card. For
every thermostat reporting to a gateway (maximum of 30 thermostats
per WEB-2xx controller and 50 thermostats per WEB-6xx/-7xx
controller) be sure you set the SAME channel value both at the
wireless communication card and the thermostat(s).
Honeywell recommends using only the channels 15 (2425 MHz)
or 25 (2575 MHz).
The default value of 10 is NOT a valid channel. Although the valid
range of available channels is from 11 to 26 use only channel 15 or 25
to avoid interference with other wireless devices.
Conditional parameter to wireless models (TB7200X5x14W)
This parameter is only available for wireless thermostats. This
parameter lets you to copy the configuration parameter settings from
a like Honeywell TB7200 thermostat. To use this command, the
thermostat you want to copy parameters from must be on the wireless
network with a network address (Com addr) and must be the same
model number as the thermostat you want to copy to.
On the thermostat you want to copy parameters to, enter the network
address (Com addr) of the thermostat you want to copy parameters
from. This process can be completed locally at the thermostat or
using the WEBStation-AX.
If the parameters copy successfully, the Get From address returns to
255. If the parameters do not copy successfully, 254 is displayed. If
the copy was not successful, verify the following:
• The thermostat to be copied is the same model as the one being
copied to.
• The thermostat to be copied is on the network.
• The correct network address (Com addr) value for the thermostat
to be copied was entered.
Leaving the Get From parameter value at 255 means that
configuration parameters will be set manually.
12