Toshiba Q9 Installation And Operation Manual page 200

Table 7. Terminal Assignments With the Associated My Function Input Setting (Input Function Target) and
Parameter Setting Numbers for the FL, O1A/O1B (OUT1), O2A/O2B (OUT2), OUT3–OUT6, R1–R4
Terminals.
Input Param
Setting Setting
1000 0 Lower-Limit (LL) Frequency
1002 2 Upper-Limit (UL) Frequency
1004 4 Low (Speed Signal)
1006 6 Acceleration/Deceleration Complete
1008 8 Reach Speed Signal
1010 10 Fault (Any)
1012 12 Fault 2 (Except EF, OCL, EPHO, OL2)
1014 14 Over-Current (OC) Alarm
1016 16 ASD Overload (OL1) Alarm
1018 18 Motor Overload (OL2) Alarm
1020 20 Over-Heat (OH) Alarm
1022 22 Over-Voltage (OP) Alarm
1024 24 DC Under-Voltage Alarm
1026 26 Low-Current Alarm
1028 28 Over-Torque (OT) Alarm
1030 30 DBR Overload (OL) Alarm (Not Used)
1032 32 Emergency Off (E-Off) Active
1034 34 Retry Active
1036 36 Pattern Operation Switching Output (Not Used)
1038 38 PID Deviation Limit
1040 40 Start/Stop
1042 42 Hard Fault (OCA, OCL, EF, Phase Failure, etc.)
1044 44 Soft Fault (OL, OC, OV)
1046 46 Bypass 1 (Comm. Power/ASD Switching Output 1)
1048 48 Bypass 2 (Comm. Power/ASD Switching Output 2)
1050 50 ASD Fan ON/OFF
1052 52 Jogging (Jog Run Active)
1054 54 (Panel/)Terminal Board Operation Switching
1056 56 Run-Time Alarm
1058 58 Comm. Alarm (ProfiBus/DeviceNet/CC-Link)
1060 60 Forward/Reverse Switching
1062 62 Ready for Operation 1 (Includes ST and Run)
1064 64 Ready for Operation 2
1066 66 POFF Alarm (Control Power Out Of Spec.)
1068 68 Brake Release (BR) (Not Used)
1070 70 Alarm Status Active
1072 72 Forward Speed Limit (Torque Control)
1074 74 Reverse Speed Limit (Torque Control)
1076 76 ASD Healthy Output
1078 78 External Communication Error
1080 80 Error Code Output 1
1082 82 Error Code Output 2
1084 84 Error Code Output 3
190
Discrete Output Terminal Assignment Selections
Function
Input Param
Setting Setting
1088 88 Error Code Output 5
1090 90 Error Code Output 6
1092 92 Data Output 1
1094 94 Data Output 2
1096 96 Data Output 3
1098 98 Data Output 4
1100 100 Data Output 5
1102 102 Data Output 6
1104 104 Data Output 7
1106 106 Light Load Detected
1108 108 Heavy Load Detected
1110 110 Positive Torque Limit
1112 112 Negative Torque Limit
1114 114 Rush Suppression Relay Activated
1118 118 Completion of Positioning (Not Used)
1120 120 L-STOP
1122 122 Power Fail Synchronize Op. (Not Used)
1124 124 Traverse in Progress (Not Used)
1126 126 Traverse Deceleration in Progress (Not Used)
1128 128 Maintenance Alarm
1130 130 Over-Torque (OT) Alarm
1132 132 Frequency Command ½ Selection
1134 134 Fault (Except Emergency Off)
1135 136 Local/Remote
1138 138 Forced Run
1140 140 Fire Speed
1142 142 Low Torque
1144 144 Frequency Control = RR
1146 146 Frequency Control = RX
1148 148 Frequency Control = VI
1150 150 PTC Alarm
1152 152 Power Loss
1154 154 4 – 20 mA Loss
1156 156 Damper Command
1222 222 My Function Output 1
1224 224 My Function Output 2
1226 226 My Function Output 3
1228 228 My Function Output 4
1230 230 My Function Output 5
1232 232 My Function Output 6
1234 234 My Function Output 7
1236 236 My Function Output 8
1238 238 My Function Output 9
Q9 ASD Installation and Operation Manual
Function