Connection Procedure, Frames R0 - ABB ACS560 Quick Installation And Start-Up Manual

78 Electrical installation
164 HI -त् व रित इं स ् ट ाले श न और स् ट ार् ट -अप गाइड
78 Electrical installation
Connection procedure, frames R0...R2
Connection procedure, frames R0...R2
￭ कने क ् श न प् र क् र िया, फ् र े म R3 ... R4
1. Remove the front cover as follows:
1. Remove the front cover as follows:
• Loosen the retaining screw with a screwdriver (1a).
If the drive is connected on an IT (ungrounded) system, make sure you have
• Loosen the retaining screw with a screwdriver (1a).
• Lift the cover from the bottom outwards (1b).
disconnected the EMC filter and Varistor (VAR). See
82 Electrical installation
• Lift the cover from the bottom outwards (1b).
1. अगले कवर को निम् न ानु स ार निकाले ं : Connection procedure, frames R3...R4
1. Remove the front cover as follows:
• एक पे ं च कस (1a) से पे ं च को ढीला करे ं ।
• Loosen the retaining screw with a screwdriver (1a).
• सबसे ऊपर वाले बक् स े (1b) को अलग करने के लिए अगले कवर को ऊपर की ओर धक् क ा दे ं , और कवर
• Push the front cover upward to uncouple top buckle (1b), and lift the cover
को नीचे से बाहर की तरफ उठाएं (1c)।
from the bottom outwards (1c).
EN
2a
1C
1b
HI
Warning! If the drive is connected on an IT (ungrounded) system, make sure
that the EMC Filter and Varistor (VAR) is disconnected. See page 71.
Warning! If the drive is connected on an IT (ungrounded) system, make sure
Warning! If the drive will be connected on an IT (ungrounded) system, make
that the EMC Filter and Varistor (VAR) is disconnected. See page 71.
sure you have disconnected the EMC Filter and Varistor (VAR). See page 71.
मोटर के ब ल
Motor cable
2. चित् र मे ं दिखाए अनु स ार के ब ल के सिरों को तै य ार करे ं । दो भिन् न -भिन् न प् र कार की मोटर के ब लों को चित् र
Motor cable
Motor cable
2. Prepare the ends of the cable as illustrated in the figure. Two different motor cable
2a और 2b मे ं दिखाया गया है ।
2. Prepare the ends of the cable as illustrated in the figure. Two different motor cable
types are shown in the figures (2a.and 2b).
2. Prepare the ends of the cable as illustrated in the figure. Two different motor cable
types are shown in the figures 2a and 2b.
टिप् प णी
[ Translation missing]
types are shown in the figures (2a.and 2b).
Note: The bare shield will be grounded 360 degrees. Note: The bare shield will be grounded 360 degrees.
Note: The bare shield will be grounded 360 degrees.
2a
2a
PE
2a
PE
PE
2b
2
b
2
b
PE
PE
PE
3. मोटर के ब ल को निम् न ु स ार कने क ् ट करे ं :
If the power cable is temporarily removed from the grounding shelf, connect the motor
and input power cables except the 360° grounding, and then reinstall the grounding
shelf.
1b
1b
1a
1a
The bare shield will be grounded 360°.
EMC फ़ ि ल् ट र ( पृ ष ् ठ
178).