Toshiba Stratagy IVP8 Installation And Maintenance Manual page 43

Table 2-1 IVP8 Strata DK Slot Assignments
Install the IVP8 in any slot in the Expansion KSU where an eight-port card can be inserted. For DK40i/
DK40/DK16e, see Chapter 2 – DK40i Configuration in the Strata DK I&M Manual for all possible
configurations.
Important!
Do not install IVP8 in slot 18 of the DK40i/DK40/DK16e.
DK40i/DK40/DK16e/DK16: A K5RCU, K5RCU2, or K4RCU3 must be installed in the Base KSU to enable
end-to-end signaling.
Note Putting a IVP8 into a Strata DK40i/DK40/DK16e/DK16, eliminates eight telephone lines.
Note For the DSS/BLF feature, the IVP8 must reside in a higher-numbered slot than the PDKU card
that the IVP8 monitors (see
Install the card in a universal slot starting with slot 12 (if a PDKU or PEKU is in slot 11) or slot 13 (if a RSIU
is in slot 11).
Important!
Do not install the IVP8 in slots 27, 28, 31, 37, 38, 47, 48, 51, 57, 58, 67, 68, 71, 77, or 78.
To enable end-to-end signaling, ensure that an RRCS -4, -8 or -12 is installed on the RCTU, and verify that
the RCTU code in Program 03 is for RRCS operation.
Important!
The IVP8 does not function when installed in slots 31 or 51.
Note For the DSS/BLF feature, the IVP8 must reside in a higher-numbered slot than the PDKU card
that the IVP8 monitors (see
DK280 (R2) — install the card in any universal slot (except slots 31 and 51), starting with slot 12 of the
Base Cabinet.
DK280 (R3 or higher) — install the card in any universal slot (except slots 31 and 51), starting with slot 12
(if a PDKU or PEKU is in slot 11) or slot 13 (if a RSIU is in slot 11).
DK280 (All releases) — To enable end-to-end signaling, an RRCS -4, -8 or -12 must be installed on the
RCTU. Verify that the RCTU code in Program 03 is for RRCS operation.
Install the card in any slot after slot 01. A CRCU must be installed to enable end-to-end signaling.
For the DSS/Busy Lamp feature to operate, the IVP8 must monitor the DSS/BLF data from a specific
PDKU card. The Strata DK telephone system restricts this capability to certain configurations. The IVP8:
•
Cannot be installed in the first slot of any cabinet (i.e., 11~71).
•
Can only monitor a PDKU that resides in an odd-numbered cabinet.
•
Must always be in a higher-numbered slot than the PDKU card, even if the PDKU is in another
cabinet.
When IVP8 is installed in an odd-numbered cabinet, the system software searches for the PDKU in all
lower-numbered card slots in that cabinet (as defined by the console_slot_id parameter on
When the IVP8 is installed in an even-numbered cabinet, the system software searches for the PDKU in all
lower-numbered card slots of the preceding odd-numbered cabinet. see
examples.
Stratagy I&M 06/02
DK40i/DK40/DK16e/DK16
DK424i/DK424
Figure 2-1 on page
DK280
Figure 2-1 on page
DK24, DK56, DK96
DSS/Busy Lamp Feature (For all Strata DK systems)
2-10).
2-10).
Figure 2-1 on
Installation
Step 4: Install Stratagy
page 4-17).
page 2-10 for
2-9