X'over Setting; Audio Preset Memory - Kenwood KIV-BT901 Instruction Manual

DSP Setup

X'Over Setting

Fine adjusting the following setting values
corresponding to the X'Over values set in the
section <Speaker Setting> (page
Display Item Range
"X'Over"
"Front" "FC" Front High Pass Filter
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 (Hz)
"SLOPE" Front High Pass Slope
-6, -12, -18, -24 dB/Oct
"Rear" "FC" Rear High Pass Filter
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 (Hz)
"SLOPE" Rear High Pass Slope
-6, -12, -18, -24 dB/Oct
"SubWoofer" "FC" Subwoofer Low Pass Filter
30, 40, 50, 60, 70, 80, 90, 100, 120,
150, 180, 220, 250, Through (Hz)
"SLOPE" Subwoofer Slope
-6, -12, -18, -24 dB/Oct
"PHASE" Subwoofer Phase
Reverse (180°)/ Normal (0°)
1
Select the source
Press the [SRC] button repeatedly also switches
source.
Select a source other than "
✍ SRC Select mode 2: Press the [SRC] button. Turn
the [Volume] knob and press it when the desired
item is displayed.
2
Enter Audio Control mode
Press the [Volume] knob.
3
Enter X'Over setting mode
Turn the [Volume] knob and press it when the
desired item is displayed.
Select "Detailed Setup"
4
Select the speaker you want to set
Turn the [Volume] knob and press it when the
desired item is displayed.
Select "Front", "Rear", or "SubWoofer".
5
Select the setting item to adjust
Turn the [Volume] knob and press it when the
desired item is displayed.
6
Make a setting
Turn the [Volume] knob to select a setting
value, and then press the [Volume] knob.
7
Repeat steps 3 to 5 to complete the X'Over
settings
52
|
KIV-BT901/ KIV-701
50).
STANDBY".
>
"X'Over".
8
Exit Audio Control mode
Press the [MENU] button for at least 1 second.

Audio Preset Memory

Registering the value setup by Sound Control.
1
Setup Sound Control
Refer to the following operations to setup the
Sound Control.
- Car Type Selection (page 50)
- Speaker Setting (page 50)
- Car Type Fine Adjustments (page 51)
- X'Over Setting (page 52)
- Manual Equalizer Control (page 47)
- Listening Position Selection (page 48)
- Listening Position Fine Adjustments (page 48)
2
Enter Audio preset memory mode
Turn the [Volume] knob and press it when the
desired item is displayed.
Select "Detailed Setup"
Memory".
3
Select the number to put in the memory
Turn the [Volume] knob and press it when the
desired item is displayed.
Select a preset number.
4
Turn the [Volume] knob and press it when the
desired item is displayed.
Select "YES".
"Completed" is displayed.
5
Exit Audio Control mode
Press the [MENU] button for at least 1 second.
⁄
• Register 6 patterns of Audio Preset Memory.
• Preset number "1":
When you press the Reset, all the sources will be the
setting value which is registered.
• Preset number "1" and "2":
The memory cannot be erased by the Reset button.
• This function cannot be registered when the iPod
Equalizer set in <Preset Equalizer Curve Select> (page
> "Preset" > "Preset
47).