X'over Setting; Audio Preset Memory - Kenwood DPX404U Instruction Manual

Function of DPX504U
DSP Setup
X'Over Setting
Fine adjusting the following setting values
corresponding to the X'Over values set in the
section <Speaker Setting> (page
Display Item
"X'Over"
"Front" "FC"
"SLOPE"
"Rear" "FC"
"SLOPE"
"SubWoofer" "FC"
"SLOPE"
"PHASE"
1
Select the source
Press the [SRC] button.
Select a source other than "STDBY".
2
Enter Function setting mode
Press the [VOL] knob.
3
Enter X'Over setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select "Audio Control"
"X'Over".
4
Select the speaker you want to set
Turn the [VOL] knob and press it when the
desired item is displayed.
Select "Front", "Rear", or "SubWoofer".
5
Select the item you want to set
Operation type
Selects the item.
Adjust each item.
Set the value
6
Repeat steps 4 to 5 to complete the X'Over
settings.
7
Exit Function setting mode
Press the [ ] button for at least 1 second.
56
|
DPX504U/ DPX404U/ DPX304
54).
Range
Front High Pass Filter
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 (Hz)
Front High Pass Slope
-6, -12, -18, -24 dB/Oct
Rear High Pass Filter
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 (Hz)
Rear High Pass Slope
-6, -12, -18, -24 dB/Oct
Subwoofer Low Pass Filter
30, 40, 50, 60, 70, 80, 90, 100, 120,
150, 180, 220, 250, Through (Hz)
Subwoofer Slope
-6, -12, -18, -24 dB/Oct
Subwoofer Phase
Reverse (180°)/ Normal (0°)
( : Factory setting)
> >
"Detailed Setup"
Operation
Turn the [VOL] knob.
Press the [4] or [¢] button.
Press the [VOL] knob.
Audio Preset Memory
Registering the value setup by Sound Control.
1
Setup Sound Control
Refer to the following operations to setup the
Sound Control.
- <Car Type Selection> (page 54)
- <Speaker Setting> (page 54)
- <Car Type Fine Adjustments> (page 55)
- <X'Over Setting> (page 56)
- <Manual Equalizer Control> (page 49)
- <Listening Position Selection> (page 50)
- <Listening Position Fine Adjustments> (page 50)
2
Enter Audio preset memory mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select "Audio Control"
"Preset" > "Preset Memory".
3
Select the number to put in the memory
Turn the [VOL] knob and press it when the
desired item is displayed.
Select a preset number.
4
Turn the [VOL] knob and press it when the
desired item is displayed.
Select "YES".
"Memory Completed" is displayed.
5
Exit Function setting mode
Press the [ ] button for at least 1 second.
⁄
•
Register 6 patterns of Audio Preset Memory.
•
Preset number "1":
When you press the Reset, all the sources will be the setting
value which is registered.
•
Preset number "1" and "2":
The memory cannot be erased by the Reset button.
•
This function cannot be registered when the iPod Equalizer
set in <Preset Equalizer curve Select> (page
> >
"Detailed Setup"
49).