Cub Cadet Time Saver i1042 Operator's Manual page 20

Zero turn riding mower time saver
Hide thumbs Also See for Time Saver i1042:
Table of Contents

Advertisement

Available languages

Available languages

Service
7
Pivot Baradjustment
If excessive play is experienced
in the steering wheel,
check the pivot bar for forward/rearward
movement.
1. Raise the front of the tractor and set it on jack stands,
so the front wheels are suspended
above the ground.
2. Grasping the ends of the pivot bar, attempt
to move
each end of the axle forward and rearward to check for
side play. There should be minimal
or no side play.
3. If there is no side play, lower the tractor to the ground
and have the steering linkage inspected
by you Cub
Cadet dealer. If there is side play, tighten
the pivot bar
as follows:
Support the pivot bar, then remove the hex lock
nuts securing the two shoulder bolts that pass
through
the pivot bar bracket, the pivot bar, and
frame. Refer to Figure 6-2.
Slide a half inch flat washer, with a maximum
thick-
ness of .030 inch, onto each shoulder bolt. Reinstall
the shoulder bolts w/washers
and fasten with the
two hex lock nuts.
Gradually and evenly tighten the hex lock nut while
continuing
to check the forward/rearward
move-
ment of the pivot bar. Tighten the lock nuts until
minimum
play, without
binding
the pivot bar's up
and down movement,
is achieved.
Checking Main Harness Fuse
A 20 amp fuse is installed in your tractor's wiring
harness to protect
the tractor's electrical
system from
damage caused by excessive amperage.
If the electrical
system does not function,
or your
tractor's engine will not crank, first check to be certain
that the fuse has not blown.
The fuse can be found inside of the dash panel behind
the battery tray. You may need to remove the battery
to gain access to the fuse. Always use a fuse with the
same amperage
capacity for replacement.
NOTE: A second fuse holder can be found inside the dash
panel. This fuse holder is used for the optional
12 volt
power outlet.
Battery
The battery
is sealed and is maintenance-free.
Acid levels
cannot be checked.
Always keep the battery cables and terminals
clean and
free of corrosive build-up.
After cleaning the battery and terminals,
apply a light
coat of petroleum
jelly or grease to both terminals.
Always keep the rubber boot positioned
over the posi-
tive terminal
to prevent shorting.
IMPORTANT: If removing the battery for any reason, discon-
nect the NEGATIVE (Black) wire from it's terminal FIRST,
followed
by the POSITIVE (Red) wire. When re-installing
the
battery, always connect the POSITIVE (Red) wire its terminal
first, followed
by the NEGATIVE (Black) wire. Be certain that
the wires are connected to the correct terminals; reversing
them could change the polarity and result in damage to
your engine's alternating
system.
Charging the Battery
If the tractor has not been put into use for an extended
pe-
riod of time, charge the battery with an automotive-type
12-volt charger for a minimum
of one hour at six amps.
WARNING:
Batteries give off an explosive
gas
while charging. Charge battery
in a well venti-
lated area and keep away from an open flame
or pilot light as on a water heater, space heater,
furnace, clothes dryer or other gas appliances.
Cleaning the Battery
Clean the battery
by removing
it from the tractor and
washing with a baking soda and water solution.
If neces-
sary, scrape the battery terminals
with a wire brush to
remove deposits. Coat terminals
and exposed wiring with
grease or petroleum
jelly to prevent corrosion.
Battery Failures
Some common
causes for battery failure are:
• incorrect
initial activation
• undercharging
• overcharging
• corroded
connections
• freezing
These failures are NOT covered by your tractor's warranty.
Changing Transmission DriveBelt
NOTE: Several components
must be removed, including
transmission
steering linkage which will have to be read-
justed, in order to change the tractor's transmission drive
belt. Contact your Cub Cadet dealer to have your transmis-
sion drive belt replaced.
Hydrostatic Transmission
Keep the area around the transmission
cooling
fan free of
grass and debris at all times. The hydrostatic
transmission
is sealed at the factory and is maintenance
free. The fluid
level cannot be checked and cannot be changed.
Off Season Storage
If the machine is to be inoperative
for a period longer than
30 days, the following
procedures
are recommended:
WARNING:
Never store the machine or fuel
container
indoors where there is an open flame,
spark or pilot light such as on water heater,
furnace, clothes dryer or other gas appliance.

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents