Stihl FH-KM Instruction Manual
  1. Manuals
  2. Brands
  3. Stihl Manuals
  4. Brush Cutter
  5. FH-KM
  6. Instruction manual
Stihl FH-KM Instruction Manual

Stihl FH-KM Instruction Manual

Hide thumbs Also See for FH-KM:
Table of Contents

Advertisement

Quick Links

Download this manual
FH-KM
2 - 14
Instruction Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FH-KM and is the answer not in the manual?

Questions and answers

Related Manuals for Stihl FH-KM

Summary of Contents for Stihl FH-KM

  • Page 1 FH-KM 2 - 14 Instruction Manual...

  • Page 2: Table Of Contents

    Working Techniques KombiSystem Because a scrub cutter is a high- speed, fast-cutting power tool with In the STIHL KombiSystem a number of different very sharp cutting blades and a long KombiEngines and KombiTools can be com‐ reach, special safety precautions bined to produce a power tool.
  • Page 3 3 Safety Precautions and Working Techniques English STIHL recommends the use of genuine STIHL Move the cutter bar to the transport position and tools and accessories. They are specifically let it snap into position. designed to match the product and meet your Carry the power tool properly balanced by the performance requirements.
  • Page 4 English 3 Safety Precautions and Working Techniques 3.4.1 Models with Loop Handle tinue to run, have a dealer repair the machine – see User Manual for KombiEngines. Watch the cutting blades at all times – do not cut areas of bushes or scrub that you cannot see. Be extremely careful when cutting high scrub or bushes, check the other side before starting work.

  • Page 5: Using The Unit

    If the scrub or bush is very dusty or dirty, spray The power scythe is used at ground level. As its the blades with STIHL resin solvent from time to blades operate like a mower bar, the unit is ideal time during cutting.

  • Page 6: Approved Kombiengines

    When correctly installed, the red line (3) (arrow Only use KombiEngines supplied or explicitly point) must be flush with the end of the coupling approved by STIHL for use with the attachment. sleeve. This KombiTool may be operated only in combi‐...
  • Page 7 7 Assembling the Unit English ► Push the gearbox (11) onto the drive tube (5), turn the gearbox (11) back and forth as neces‐ sary. ► Pull the protective cap off the end of the drive tube and keep it in a safe place. If the plug comes out of the drive tube when you pull off the cap: Once the end of the drive tube is inserted...

  • Page 8: Adjusting The Cutter Bar

    English 8 Adjusting the Cutter Bar Adjusting the Cutter Bar Angle Adjuster - 145° ► Pull back the sliding sleeve (1) and use the lever (2) to adjust the joint by one or several holes. ► Release the sliding sleeve (1) and make sure the lock pin engages the quadrant (3).

  • Page 9: Fitting The Harness

    9 Fitting the Harness English Full Harness ► Shut off the engine. ► Fit the blade scabbard. ► Pull back the sliding sleeve (1) and use the lever (2) to swing the joint upwards – in direc‐ tion of drive tube – until the cutter bar is flat against the drive tube.

  • Page 10: Starting / Stopping The Engine

    English 10 Starting / Stopping the Engine Disconnecting Machine from Harness ► Place the machine on the ground so that it rests securely on the engine support and the gearbox. ► Press down the bar on the carabiner (1) and ►...

  • Page 11: Storing The Machine

    12 Storing the Machine English 11.1 Blade Drive Gear NOTICE Lubricate the blade drive gear with STIHL gear lubricant for hedge trimmers – see "Special Do not completely fill the gearbox with grease. Accessories". ► Unscrew the tube of grease from the filler hole.

  • Page 12: Minimize Wear And Avoid Damage

    If these maintenance operations are not carried Sound and vibration data measurements on out as specified, the user assumes responsibility power tools with the FH-KM KombiTool include for any damage that may occur. Among other idling and rated maximum speed with the same parts, this includes: duration of exposure.

  • Page 13: Maintenance And Repairs

    Sound power level L in accordance When repairing the machine, only use replace‐ with ISO 3744 ment parts which have been approved by STIHL for this power tool or are technically identical. KM 56 R: 105 dB(A) Only use high-quality replacement parts in order...

  • Page 14: Ukca Declaration Of Conformity

    KMA 135 R, KMA 80.0 R, Technical documents deposited at: KMA 120.0 R) ANDREAS STIHL AG & Co. KG EN ISO 12100, EN ISO 11806-1 (in conjunction with the specified FR models) The year of manufacture is indicated on the power tool.
  • Page 15 21 UKCA Declaration of Conformity English 0458-476-0121-D...
  • Page 16 *04584760121D* 0458-476-0121-D...

This manual is also suitable for:

42437405006

Table of Contents