ENACFIRE G20 - Wireless Earbuds Manual

Packaging List

Product Overview

1. Charging port
2. Charging ease LED light

3. Multifunctional button
4. Earphone LED
5. Earphone Mic
6. Acoustic hole
7. L / R Logo
8. Magnetic Charging Pin
9. Speaker

Power On & Pairing

Approach 1- With Charging Case

Power On: Take out the earphones from the charging case with Blue light on
Pairing: Earphones will Start pairing automatically With Right earphone Blue and White light flash alternately
Connection: Select 'ENACFIRE G20' from the device's Bluetooth list

Note: Right earphone is the master earphone

Approach 2 - Earphones Standalone

Power On: Touch the multifunctional buttons for 1 second.
Release when you hear the prompt sound Power on' with Blue light on

Pairing: Earphones will start pairing automatically with Right earphone Blue and White light lash alternately

Connection: Select 'ENACFIRE G20' from the device's Bluetooth list

Note: Right earphone is the master earphone

Incoming call

Answer cell/End cell

Tap the Left/Right multifunctional button once

Reject call

Touch the Left/Right multifunctional button for 2 seconds

Music

Pause/ Play

Tap the Left/Right multifunctional button once to pause/play music in the music mode (Some phones may require to start a media player first)

Voice Assistant

To launch your Device's Voice Assistant, top the Left/Right multifunctional button 3 times with the 'Beep" prompt sound

Next song

Double-tap the Right multifunctional button

Previous song

Double-tap the Left multifunctional button

Adjust Volume

Touch and hold the Left multifunctional button to decrease volume
Touch and hold the Right multifunctional button to increase volume

Note: Above functions are not supported when the earphone Is used in single.
Prompt sound 'Beep' will produce when the volume reach minimum or maximum level.

Power Off

Mode 1

Put the earphones back to the charging case, they will power off automatically

Note: Put only the Left earphone Into the charging case, the Right earphone will stay connected. Put only the Right earphone Into the charging case, the Left earphone will disconnect and start pairing.

Mode 2 Earphones Standalone

Tum off Bluetooth to disconnect the earphones.
Touch either one multifunctional button for 8 seconds to power off earphones.

Single Mode

Note: There will be two 'ENACFIRE G20' Bluetooth names for Left and Right earphones. Please select accordingly.

Charging

Earphones charging Status

Leftmost LED light fleshing: Left earphone is charging
Rightmost LED light flashing: Right earphone is charging
LED lights off: Fully charged

Note: It takes about 1,5 hours to fully charge the earphones.

Charging case charging Status

Lights on charging ease stands for the remaining battery capacity

Note: It takes about 1,5 - 2 hours to fully charge the charging case

1/4 Battery Left.
2/4 Battery Left.
3/4 Battery Left.
Fully charged

Note
Please follow below steps when both earphones fall to pair each other or occur in connection related issues.

1. Place both earphones to charging case and remain charging
2. Touch and hold the power buttons of both earphones far 8s until Blue and White lights flash
3. Take out both earphones from charging case
4. Delete the 'ENACFIRE G20' Bluetooth name from your phone and turn off Bluetooth
5. Turn on Bluetooth and click "ENACFIRE G20' from your phone

Safety Instruction

Using earphones at high to moderate volumes far extended periods of time will result in permanent hearing damage. It is advised that you keep volume levels moderate to low at all times for your safety.

Do not use while driving, cycling, operating machinery or performing other activities that require hearing surrounding sounds.

Do not use earphones in thunderstorm weather. The earphones may not work property in the bad weather condition and may increase the risk of being hit by lightning,

Earphones may not work properly under high temperature or high humidity conditions.

Do not use any corrosive cleaner/oil to clean the earphones. If the earphones come in contact with liquids, quickly wipe away. If submersed in the water, do not turn the earphones on until it is completely dried,

Tips: Warranty void if the earphones submersion in the water Keep the earphones and the packaging out of reach of children„

Customer Support

support@enacfireglobal.com (US/CA)
moongu@enacfireglobal.com WK)
Tel: +86 755 82792007

We will reply to you within 24 hours and 100% solve your issues

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download ENACFIRE G20 - Wireless Earbuds Manual