Advertisement
Quick Links
Midmount Toolbar System
Sand Pro
Model No. 08838—Serial No. 400000000 and Up
Important:
Before installing the mid-mount toolbar system, you should obtain one of the toolbars
available for use with the system. For more information, contact an authorized Toro distributor.
Setup
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
© 2021—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
/Infield Pro
Description
No parts required
Bolt (5/16 x 2-1/4 inches)
Nut (5/16 inch)
Scarifier lift-handle assembly
Bolt (1/2 x 3-1/4 inches)
Thin locknut (1/2 inch)
Detent plate
Knob
Pivot tube
Extension spring
Spring rod
Pivot tube bracket
Bolt (3/8 x 3 inches)
Locknut (3/8 inch)
Spring bracket
Bolt (3/8 x 2-3/4 inches)
Adjustable rod assembly
Bolt (1/2 x 1-1/2 inches)
Locknut (1/2 inch)
Screen panel
HWH screw (#10 x 1/2 inch)
Right-hand saddle assembly
Left-hand saddle assembly
Bolt (5/16 x 1 inch)
Locknut (5/16 inch)
Toolbar (sold separately)
Register at www.Toro.com.
®
3040 and 5040 Traction Unit
Qty.
–
2
2
1
2
2
1
1
1
1
1
2
4
6
1
1
1
1
2
1
2
1
1
4
4
1
Original Instructions (EN)
Form No. 3445-481 Rev A
Operator's Manual
Use
Prepare to install the toolbar.
Install the scarifier lift-handle assembly.
Install the pivot tube and the tension
spring.
Install the adjustable rod assembly.
Install the screen panel and saddles.
Install a toolbar.
*3445-481*
Printed in the USA
All Rights Reserved
Advertisement
Related Manuals for Toro 08838
Summary of Contents for Toro 08838
- Page 1 Operator's Manual Important: Before installing the mid-mount toolbar system, you should obtain one of the toolbars available for use with the system. For more information, contact an authorized Toro distributor. Setup Loose Parts Use the chart below to verify that all parts have been shipped.
- Page 2 Procedure Description Qty. Lever assembly Bolt (5/16 x 2 inches) Locknut (5/16 inch) Pivot tab Toolbar link Carriage bolt (3/8 x 1-1/4 inches) Spacer Install the toolbar lift pedal. Washer (1 inch) Locknut (3/8 inch) Pedal lever assembly Retaining ring Washer (7/8 inch) Bolt (5/16 x 1 inch) Eccentric bolt...
- Page 3 Remove the 4 flange-head screws that secure the right-hand wheel shroud to the frame (Figure g003477 Figure 1 1. Right-hand wheel shroud g025726 4. Screen panel Figure 2 2. Nut (2) 5. Screws 1. Bolt (1/2 x 3-1/4 inch) 4. Thin locknuts (1/2 inch) 3.
- Page 4 Note: There must be a minimum clearance of 3 mm (1/8 inch) between the hydraulic line and the lift handle assembly. Gently position the hydraulic line as required (Figure Installing the Pivot Tube and the Tension Spring Parts needed for this procedure: g019398 Pivot tube Figure 3...
- Page 5 Loosely install the pivot tube bracket onto the right side (Figure Slide the right-hand side of the pivot tube into the right side pivot tube bracket (Figure Installing the Adjustable Insert the spring rod into the hole in the spring bracket, and loosely secure it with a locknut (3/8 Rod Assembly inch).
- Page 6 on the pivot tube until it is on the left side of the rod lever. Note: You can move the pivot tube up or down in its brackets to gain clearance for mounting Installing the Screen Panel the adjustable rod. Move the lift handle until the hole in the ball and Saddles joint aligns with the hole on the right-side of...
- Page 7 Note: Position the saddles as shown in Figure g345308 Figure 10 1. Bolt (5/16 x 1 inch) 3. Lift arm 2. Saddle 4. Locknut (5/16 inch) g004101 Figure 11 1. Toolbar 3. Fourth tooth 2. Pivot bracket 4. Tooth mounting hardware Position each end of the attachment tube onto Installing a Toolbar the saddles.
- Page 8 Installing the Toolbar Lift Pedal Parts needed for this procedure: Lever assembly Bolt (5/16 x 2 inches) Locknut (5/16 inch) Pivot tab Toolbar link g345309 Figure 13 Carriage bolt (3/8 x 1-1/4 inches) Spacer 1. Lever assembly 3. Bolt (5/16 x 2 inches) 2.
- Page 9 g004105 Figure 16 1. Pivot tab 5. Washer (1 inch) 2. Toolbar link 6. Washer (13/16 inch) 3. Carriage bolt (3/8 x 1-1/4 7. Locknut (3/8 inch) inches) g345310 Figure 15 4. Spacer 1. Toolbar link 4. Retaining ring 2. Pedal lever assembly 5.
- Page 10 Rotate the ball joint shown in Figure 19 change the length of the rod as follows: • To increase the gap, shorten the rod. • To decrease the gap, lengthen the rod. Adjusting the Pivot Spring Install the rod with the bolt and the locknut, and test the clearance again.
- Page 11 Note: Rotate the eccentric bolt either direction until the If the teeth on one side of the toolbar toolbar tines are parallel to the notch in the lift contacts the ground before the other side, level (Figure 17 Figure 21). the toolbar.
- Page 12 Reading and Storing the Documentation No Parts Required Procedure Read the documentation. Store the documentation in a safe place.
-
Page 13: Operation
Operation • To lower the toolbar, move the lift handle to the left, lower it, and then slide it to the right into the desired detent position. • To raise the toolbar, move the lift handle to the left, raise it, and then slide it to the right into the desired detent position. -
Page 14: Troubleshooting
1. The traction unit tilts when turning tight 1. Install the optional stiffer sidewall tires turning the machine. corners or circles. available from your authorized Toro distributor. The machine stops when it hits an 1. The adjuster rod is installed incorrectly 1. - Page 15 Notes:...
- Page 16 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact your Authorized Toro Service Center.