Table of Contents
Advertisement
Available languages
Available languages
Moving the Pressure Washer (Fig. A–E)
1. Turn OFF the pressure washer unit
selector switch
9
to the center position. Then turn off
the water supply.
2. Point the spray wand
trigger
to release remaining water pressure.
7
3. When the spray wand is completely empty, pull up the
telescoping handle
12
using the wheels
15
Shutdown (Fig. A, E, L)
1. Turn OFF the pressure washer unit
speed selector switch
off the water supply and remove the battery packs from
the pressure washer unit
2. Discharge residual pressure by squeezing the trigger
until no more water comes out of the spray wand
3. Engage the spray trigger lock‑off
4. Disconnect the garden hose from the water intake
5. Disconnect the high pressure hose
pressure water outlet
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Nozzle Cleaning (Fig. A, R)
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
If the nozzle becomes clogged with foreign materials, such as
dirt, excessive pressure may develop. If the nozzle becomes
partially clogged or restricted, the pump pressure will pulsate.
Clean the nozzle immediately using the nozzle cleaner.
1. Turn OFF the pressure washer unit
speed selector switch
2. Turn off the water supply and remove the battery packs
from the pressure washer unit
3. Pull trigger
7
on spray handle
water pressure.
4. Remove the nozzle from the spray wand
the quick connect collar
5. Using the nozzle cleaning tool
from the nozzle.
6. Run water from a faucet or garden hose through
the nozzle.
8
toggle the speed
in a safe direction and pull the
2
and pull the pressure washer unit
to your next location.
8
by toggling the
9
to the center position. Then turn
8
.
6
.
1
from the high
18
and drain hose.
8
by toggling the
9
to the center position.
8
.
4
to relieve any
2
by pulling
3
toward the spray wand.
26
, unclog any debris
Suction Hose (Fig. A, L)
1. To clean the suction hose
pressure washer.
2. Pull the trigger switch to relieve any water pressure.
3. Remove the suction hose
4. To clean the suction hose, use water from a garden hose
to thoroughly rinse out the suction hose and allow it to
fully dry.
Suction Hose Filter (Fig. S)
1. Turn the filter
counterclockwise and remove.
2. Remove the strainer from inside of the filter.
3. Rinse all of the parts with clean water and reassemble.
MAINTENANCE
7
WARNING: To reduce the risk of serious personal
2
.
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
17
.
installing attachments or accessories. An
accidental start‑up can cause injury.
Your D
WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Storage (Fig. A, D, F, T)
•
Store in a dry, covered location above freezing temperature
with the batteries removed. STORE INDOORS.
•
Always completetely empty water from high pressure
hose, pressure washer unit, nozzles, and spray wand.
•
Nozzles can be stored in the nozzle storage slots on the
handle grip as shown in Fig. A.
•
High pressure hose and suction hose can be stored coiled
up and secured between the cage and the pressure
washer unit
•
Spray wand can be stored, broken down into three
pieces, in the storage compartment
Fig. F and Fig. T.
•
High pressure foam cannon
the built in storage space in the pressure washer unit as
shown in Fig. T.
•
Turbo nozzle can be stored in the storage
compartment
•
Pressure washer unit
horizontally, but only stack things on top of unit in the
horizontal storage position as shown in Fig. D
Repairs
The charger and batteries are not serviceable. There are no
serviceable parts inside the charger or battery pack.
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including
brush inspection and replacement, when applicable)
should be performed by a factory service center or
an authorized service center. Always use identical
replacement parts.
, shut off the
27
27
from the pressure washer.
29
on the end of the suction hose
8
as shown in Fig. D.
34
25
can be stored empty, in
34
as shown in Fig. F and Fig. T.
8
can be stored vertically or
English
27
as shown in
15
Advertisement
Table of Contents
