Table of Contents
Advertisement
Available languages
Available languages
2. Securely tighten the suction hose collar
nOTE: Always disconnect the suction hose after usage.
3. Place other end of suction hose, with the filter
into a container of fresh water or a fresh water source.
4. Adjust the float ball
28
filter
29
stays covered in the liquid.
5. Select the correct nozzle to be used. Attaching Nozzles
6. After the job being performed is complete, place the
suction hose into a container of clean water and draw the
clean water through the system to rinse.
nOTE: When using the suction hose, it may take a few
minutes for the pressure washer to self prime. Ensure the
pressure washer is turned on and the trigger on the spray
wand it being pulled until primed.
Removing High Pressure Foam Cannon
from Storage (Fig. A)
Always completely empty the high pressure foam cannon
before storing.
1. To remove the high pressure foam cannon
built in storage space in the pressure washer unit, grasp
the high pressure foam cannon
pull it out and away from the pressure washer unit.
2. To place the high pressure foam cannon
storage slot, press the high pressure foam cannon
firmly into the storage slot until it snaps into the built in
storage space in the pressure washer unit.
3. Ensure that soap bottle
position by gently tugging on the soap bottle
Attaching High Pressure Foam Cannon
(Fig. M)
1. To connect the high pressure foam cannon
spray wand
, pull the quick connect collar
2
the spray wand and insert the soap bottle.
2. Release the quick connect collar
pressure foam cannon
3. Give the high pressure foam cannon
the quick connect collar has locked into place to ensure
the high pressure foam cannon
4. To adjust the rate of foam, rotate the pressure control
knob
39
on the top of the high pressure foam cannon
25
counterclockwise for less or clockwise for
more foam.
nOTE: The soap bottle should be positioned underneath the
spray wand. Do not position the high pressure foam cannon
above the spray wand as this will lead to soap dripping
on the spray wand. The spray tip on the high pressure
foam cannon
rotates for vertical or horizontal application.
25
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
30
by hand.
29
on the suction hose so the
25
from the
25
with one hand and
25
into its
25
is secured into the storage
25
to the
25
toward
3
3
to lock the high
25
in place.
25
a firm tug after
is locked into place.
25
Installing and Removing the Battery Packs
(Fig. N, O)
on it,
This pressure washer is designed to operate on two battery
packs of equal capacity. The pressure washer will not operate
on a single battery pack, and If using different capacity
battery packs, the smaller capacity battery pack, when
depleted, will cause the unit to turn off
nOTE: For best results, make sure your battery packs are
both fully charged.
To Install the Battery Packs
WARNING: Ensure speed selector switch is in the OFF,
centered position, before installing battery packs.
CAUTION: Unit stops running when the battery port
door is open. If the speed selector switch is in the HI or
LO position the unit will power ON when the battery
port door closes.
CAUTION: Do not hold the trigger when closing the
25
battery port door.
1. Unlock the battery port door
port door latch
battery port door open to access the battery port.
2. Align the battery packs
battery port and slide them in until the battery packs
25
are firmly seated in the tool and ensure that they will
not disengage.
3. Lock the battery port door
door
20
.
4. Rotate the battery port door latch
the battery port door. Ensure the battery port door is fully
latched into position before starting tool.
nOTE: The unit will not operate if the battery port door is
not fully closed and latched.
To Remove the Battery Packs
1. Rotate the battery port door latch
and pull the battery port door open to access the
battery packs
2. Press the battery release buttons
packs
34
3. Insert the batteries into a charger as described in the
charger section of this manual.
4. Close the battery port door
pressure washer unit
port door is fully latched into position.
Proper Hand Position (Fig. P)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the spray handle
grip
5
and the other hand on the spray handle
20
, rotate the battery
21
counterclockwise and swing the
34
with the rails inside the
10
, close the battery port
so it seals to the pressure washer unit
21
34
.
35
and firmly pull the battery packs out of tool.
10
so it seals to the
8
and lock it. Ensure the battery
English
8
.
clockwise to lock
21
counterclockwise
on the battery
4
.
13
Advertisement
Table of Contents
