Advertisement
4.4. LOCATION
The SAC12000 should be located on a flat floor and be 500mm clear of any surrounding objects.
5. OPERATION
5.1.
CONTROL PANEL AND DISPLAY
5.1.1.
The display on the front face of the unit will only light when the unit is in cooling mode.
5.2.
SETTINGS
5.2.1.
START UP AND SHUTDOWN
5.2.1.1.
Press POWER to turn the unit ON (fig.5 #4).
5.2.1.2.
Press MODE button to select the desired operation mode (fig.5 #2).
5.2.1.3.
Press POWER again to turn the unit OFF (fig.5 #4).
5.2.2.
OPERATION MODE
The unit has four operation modes: Cool, dehumidifier, fan and sleep.
5.2.3.
COOLING A ROOM
5.2.3.1.
Select the COOL mode to lower the temperature in a room.
5.2.3.2.
Press MODE button (fig.5 #2) until the COOL indicator illuminates (fig.5 #10).
5.2.3.3.
Press the UP or DOWN button (fig.5 #3 #5) to adjust the temperature to the desired level. The temperature will be displayed on
the screen (fig.5 #9). The temperature can be set between 16ºC to 32ºC.
5.2.3.4.
Press the Speed button (fig.5 #6) Until the desired fan speed indicator illuminates (fig.5 #8).
NOTE: The horizontal air flow direction is controlled by adjusting the air outlet louvres (fig.1).
WARNING! The air conditioner function will stop if the room temperature is lower than the selected temperature.
‰
5.2.4.
VENTILATE THE ROOM
5.2.4.1.
Press the MODE button (fig.5 #2) until the FAN indicator illuminates (fig.5 #10).
NOTE: In ventilation mode the room air is circulated NOT cooled.
5.2.4.2.
Press the Speed button (fig.5 #6) Until the desired fan speed indicator illuminates (fig.5 #10).
5.2.5.
DRYING THE ROOM
5.2.5.1.
Press the MODE button on the control panel (fig.5 #2) until the DRY indicator illuminates (fig.5 #10), or press the DRY button on
the remote control (fig.6).
5.2.5.2.
Connect the drain hose (fig.7) To the drain outlet at the bottom of the unit (fig.6). See section 5.5.
NOTE: In this mode the fan speed is set to low level and cannot be changed.
5.2.6.
SLEEP MODE
WARNING! This function can only be activated by using the SLEEP button on the remote control (fig.6).
‰
To activate the sleep mode the unit must be in the COOL mode.
5.2.6.1.
To activate COOL mode press the COOL button on the remote control and then press the SLEEP (fig.6).
NOTE: After 1 hour the pre-set temperature is increased by 1ºC and increased again by 1ºC the following
hour.
5.2.7.
TIMER SETTING (1 to 24 hours)
5.2.7.1.
The TIMER has two ways of operation and can be activated by either the button on the control panel
(fig.5 #7) or by the TIMER button on the remote control (fig.6).
© Jack Sealey Limited
1
LOCK
2
MODE
3
UP
4
POWER
5
DOWN
6
SPEED
7
TIMER
8
FAN SPEED
INDICATOR
9
DIGITAL
DISPLAY
10
MODE
INDICATOR
fig.5
Original Language Version
Press to turn ON or OFF the child lock function
Press to switch operation mode between cooling,
dehumidifier and fan
Increase temperature (16ºC~32ºC) or timer setting
Press to turn the unit ON or OFF
Decreasing the temperature or timer setting
Press to switch the fan speed between HIGH or LOW
Sets a time for the unit to automatically START or STOP
Displays HIGH or LOW fan speed
Displays timer setting and room temperature
Mode display between Cooling, Dehumidifying and Fan
SAC12000.V5, SACWK1 Issue 1 09/01/23
fig.6
Advertisement
