Electrical And Mechanical Specifications - Mitsubishi Electric Melsec Q Series User Manual

3 Specifications

3.2 Electrical and mechanical specifications

Item
Consumed VA Voltage
circuit
Current
circuit
Internal current
consumption (5 V DC)
Operating temperature
Operating humidity
Storage temperature
Storage humidity
Operating altitude
Installation area
Operating environment
Vibration resistance
Impact resistance
Over voltage category *
2
Pollution degree *
Equipment category
Applicable Voltage input
wire terminal
(Usable
electric
wire)
Current input
terminal *
Tightening torque
Commercial frequency
withstand voltage
Insulation resistance
*6
Standard
Dimensions
Mass
*1. This indicates the assumed area of electric distribution to which the device is connected, the area
ranging from public distribution to factory machinery. The category II applies to the device
power-supplied from fixed facility. The surge voltage of this product is 2500 V up to the rated voltage of
300 V.
*2. The index indicates the level of conductive substance at the device's operating environment.
Contamination level 2 means only non-conductive substance. However, occasional condensation may
lead to temporary conduction.
*3. At the connection between the secondary terminal of current sensor (k, l) and the main module terminal
(1k, 1l, 3k, 3l), use twisted pair cable .
Each phase 0.1 VA (at 110 V AC), Each phase 0.2 VA (at 220 V AC)
Each phase 0.1 VA (secondary side of current sensor)
0.17 A
0 °C to +55 °C (Average daily temperature +35 °C or below)
5 % to 95 % RH (No condensation)
-25 °C to +75 °C
5 % to 95 % RH (No condensation)
2000 m or below
Inside a control panel
No corrosive gas
Conforms
to JIS B
3502, IEC
Intermittent
61131-2
vibration
Continuous
vibration
Conforms to JIS B 3502, IEC 61131-2 (147m/s
1
II or less
2 or less
Class Ι
Single wire
4
Stranded wire *
Single wire
3
4
Stranded wire *
Module-fixing screws (M3 screw) *
Between voltage/current input terminals - FG terminal
Between voltage/current input terminals - sequencer power
source and GND terminals
5 MΩ or more (500 V DC) at locations above
EMC: EN61131-2:2007, EN61326-1:2013
LVD: EN61131-2:2007, EN61010-1:2010
UL Standards: UL508
c-UL Standards: CSA C22.2 No.142
KC Marking
27.4 mm (W) x 98 mm (H) x 90.5 mm (D) excluding protruding portions
0.1 kg
Specifications
Frequency Constant
acceleration
5 Hz to 8.4 Hz -
8.4 Hz to 9.8 m/s
150 Hz
5 Hz to 8.4 Hz -
8.4 Hz to 4.9 m/s
150 Hz
AWG24 to AWG17
(φ0.5 mm to 1.2 mm)
AWG20 to AWG16
(0.5 mm
AWG24 to AWG17
(φ0.5 mm to 1.2 mm)
AWG20 to AWG16
(0.5 mm
0.36 N▪m to 0.48 N▪m
5
3 - 2
QE81WH
Half Sweep time
amplitude
3.5 mm XYZ
2 each
-
direction 10
times
1.75 mm -
2 -
2
, XYZ each direction 3 times)
2 2
to 1.3 mm )
2 2
to 1.3 mm )
2210 V AC
5 sec
2210 V AC
5 sec