Lumberjack BS200 Safety And Operating Manual
  1. Manuals
  2. Brands
  3. Lumberjack Manuals
  4. Saw
  5. BS200
  6. Safety and operating manual

Lumberjack BS200 Safety And Operating Manual

8” band saw
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
SAFETY AND OPERATING MANUAL
8" BAND SAW
BS200
ORIGINAL INSTRUCTIONS
BS200

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BS200 and is the answer not in the manual?

Questions and answers

Related Manuals for Lumberjack BS200

Summary of Contents for Lumberjack BS200

  • Page 1 SAFETY AND OPERATING MANUAL 8” BAND SAW BS200 ORIGINAL INSTRUCTIONS BS200...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS Welcome to Lumberjack! Dear customer, Congratu n your purchase. Before using the Product for the first me please be sure to read these instruc ons for use. They provide you with all informa necessary for using the product safely and to ensure its long service life.

  • Page 3: General Power Tool Safety Warnings

    Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left increase the risk of electric shock. attached to a rotating part of the power tool may result in personal injury. BS200...
  • Page 4 Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. BS200...
  • Page 5 7.9 Store the machine in a safe manner when not being used. The storage location must be dry and lockable. This prevents the machine from storage damage and from being operated by untrained persons. BS200...

  • Page 6: Symbols

    The machine must be disconnected from the supply before maintenance! Disconnect the mains plug prior to the repair, cleaning, and maintenance of the saw! Keep children and bystanders off and away. BS200...

  • Page 7: Specifica Ons

    Main Machine 6. Operator’s Manual 2. Push Stick 7. Allen Key, 4mm 3. Work Table 8. Allen Key, 3mm 4. Rip Fence 9. Blade Key 5. Table Insert 10. Hardware Bag BS200...

  • Page 8: Assembly

    4. Fasten the work table with three nuts M6 and three flat washers. 5. Attach two screws and two knurled nuts with U shape block that were removed in BOTTOM step one and fasten. M6 Nut × VIEW M6 × 16 × 3 Table Insert Work Table BS200...
  • Page 9 2. Hang the push stick on the screw. × × M6 Nut × M6 × 35 × 1 Rip Fence Clamp the rip fence. It can be used on both sides of blade. Locker BS200...

  • Page 10: Features & Set Up

    Rip Fence Work Table Door Lock Lower Housing Door Setting Knob for Blade Guard Push Stick Locking Knob for Blade Guard Setting Knob for Blade Tracking Adjustment Blade Setting Knob for Work Table Power Cord and Plug Suction Connector Motor BS200...
  • Page 11 Saw Table Lateral Alignment 1. Loosen the three fastening screws that hold the lower table trunnion. 2. Align working table so that the blade runs through the centre of the table insert’s slot. 3. Tighten the three fastening screws again. BS200...
  • Page 12 Locking Nut Locking Knob Setting Knob 3 mm 5. Tighten locking nut. Setting Up the Rip Fence The rip fence is clamped to the front. It can be used on both sides of the blade. BS200...

  • Page 13: Ope N & Maintenance

    The saw can be switched on by pressing the Machine has suction connector, green pushbutton. user can connect the machine to a proper suction unit when working. The red pushbutton has to be pressed to switch off the machine. BS200...
  • Page 14 4. To remove the band saw blade, guide it through the slot in the working table. 5. Fit fresh band saw blade. Ensure correct position: the teeth must point towards the front of the saw (where the doors are). BS200...
  • Page 15 ● Turn setting knob clockwise if the band saw blade runs towards the front of the saw. ● Turn setting knob counter- clockwise if the band saw blade runs towards the rear of the saw. 3. Tighten locking nut. BS200...
  • Page 16 2. Loosen the thrust bearing’s locking screw. necessary replace both guide pins 3. Adjust thrust bearing position (distance at the same time. thrust bearing - band saw blade = 0.5 mm BS200...
  • Page 17 - band saw blade = 0.5 mm 1. Remove table insert from saw table (push - if the band saw blade is turned by hand, it up from underneath). shall not touch the thrust bearing. 2. Fit new table insert. Table Insert BS200...

  • Page 18: Trouble Sho

    1. Change the saw blade 1. Blunt saw blade Saw blade jams 2. Clean the saw blade 2. Deposits on the saw blade during cutting work 3. Set the saw blade guide according 3. Guide has been set poorly to the operating instructions BS200...

  • Page 19: Lumberjack Guarantee

    1.2.7 The product has not been used for 1.2.3 If asked to do so by lumberjack or hire purposes. its Authorised Dealer, you return the product at your own cost to 1.2.8 The product has been purchased by...
  • Page 20 2. Claims Procedure 2.4 Please note that it is essential that the letter of claim reaches Lumberjack on the last day of this 2.1 In the first instance please contact the guarantee at the latest. Late claims will not be Authorised Dealer who supplied the product to considered.

  • Page 21: De On Of Conformity

    DECLARATION OF CONFORMITY BS200...

  • Page 22: Parts List

    PARTS LIST BS200...
  • Page 23 PARTS LIST BS200...

  • Page 24: Parts Diagram

    PARTS DIAGRAM BS200...

Table of Contents