Related Manuals for Lumberjack SCMS210SB
Summary of Contents for Lumberjack SCMS210SB
- Page 1 SAFETY AND OPERATING MANUAL SINGLE BEVEL SLIDING COMPOUND MITRE SAW SCMS210SB ORIGINAL INSTRUCTIONS SCMS210SB...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Welcome to Lumberjack! Dear customer, Congratulations on your purchase. Before using the Product for the first time please be sure to read these instructions for use. They provide you with all information necessary for using the product safely and to ensure its long service life. -
Page 3: General Power Tool Safety Warnings
A wrench or a key left c) Do not expose power tools to rain or wet attached to a rotating part of the power tool may conditions. Water entering a power tool will result in personal injury. increase the risk of electric shock. SCMS210SB... - Page 4 Use power tools only with specifically operate the power tool. Power tools are designated battery packs. Use of any other dangerous in the hands of untrained users. battery packs may create a risk of injury or fire. SCMS210SB...
- Page 5 8.2 Make sure that the guard operates properly complete stop. Correct the cause for the jamming and that it can move freely. Never lock the of the saw blade before restarting the machine. guard in place when opened. SCMS210SB...
- Page 6 (such as wood or a rough‐coated held more secure than by hand. surface) that does not have a reflective Surface 8.19 Never leave the machine before it has come to a complete stop. Cutting tools that are still running can cause injuries. SCMS210SB...
- Page 7 Any repairs must be cable completely. carried out by the laser manufacturer or an authorized service agent. 9.12 Do not attempt to repair the laser guide by yourself. 9.13 Do not attempt to change any parts of the laser guide. SCMS210SB...
-
Page 8: Symbols & Cable Rating Chart
Caution: Laser radiation. Do Caution! Wear a dust mask. not look into the beam! Laser class 2 product! Amperes 7.5M 0 – 2.0 2.1 – 3.4 3.5 - 5.0 5.1 – 7.1 7.1 – 12.0 12.1 – 20.0 SCMS210SB SCMS210SB... -
Page 9: Machine Details And Product Features
–45° to +45° as well as bevel angles from ‐45° to 45° are possible. The capacity of the power tool is designed for sawing hardwood and softwood. The power tool is not suitable for cutting aluminium or other non‐ferrous metals or alloys. SCMS210SB SCMS210SB... -
Page 10: Assembly
Only lift the saw by the operating handle (5) or outer castings. Do not lift the saw using the guards. SCMS210SB... -
Page 11: Changing The Blade
– Lower the blade guard hold the rotating lower dust that is especially detrimental to health or blade guard (8) and blade bolt cover carcinogenic, use a special dust extractor. (10) in position and tighten the fixing screw to secure the blade bolt cover in position. SCMS210SB... -
Page 12: Operation
The depth of cut can be pre‐set for even and lock (12). repetitive shallow cuts. – Adjust the 0° bevel adjustment screw (29) – Slide the stop plate (24) towards the front using a 4mm hex key to bring the saw blade position. into alignment with the square. SCMS210SB... -
Page 13: Working Advice
When transporting the power tool, use only the transport devices and – Do not stand in a line with the never use the protective devices. saw blade in front of the machine. Always stand aside of the saw blade. SCMS210SB... -
Page 14: Maintenance And Service
Therefore, always keep the area around the electric shock or injury. retracting blade guard clean. Remove dust and chips after each working procedure with a brush or by blowing out with compressed air. Keep the tool’s air vents unclogged and clean at all times. SCMS210SB... -
Page 15: Lumberjack Guarantee
1.2.7 The product has not been used for 1.2.3 If asked to do so by lumberjack or hire purposes. its Authorised Dealer, you return the product at your own cost to 1.2.8 The product has been purchased by... - Page 16 2.4 Please note that it is essential that the letter of 2. Claims Procedure claim reaches Lumberjack on the last day of this 2.1 In the first instance please contact the guarantee at the latest. Late claims will not be Authorised Dealer who supplied the product to considered.
-
Page 17: Declaration Of Conformity
SCMS210SB... -
Page 18: Parts List
PARTS LIST SCMS210SB... - Page 19 PARTS LIST SCMS210SB...
- Page 20 PARTS LIST SCMS210SB...
-
Page 21: Parts Diagram
PARTS DIAGRAM PART 1 SCMS210SB... - Page 22 PARTS DIAGRAM PART 2 SCMS210SB...
- Page 23 PARTS DIAGRAM FULL SCMS210SB...
Need help?
Do you have a question about the SCMS210SB and is the answer not in the manual?
Questions and answers