Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Lumberjack BS305
Summary of Contents for Lumberjack BS305
- Page 1 305mm/340mm Band Saw with Stand BS305/BS340 ORIGINAL INSTRUCTIONS BS305/BS340...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Welcome to Lumberjack! Dear customer, Congratulations on your purchase. Before using the product for the first time please be sure to read these instructions for use. They provide you with all information necessary for using the product safely and to ensure its long service life. -
Page 3: General Power Tool Safety Warnings
A wrench or a key left c) Do not expose power tools to rain or wet attached to a rotating part of the power tool may conditions. Water entering a power tool will result in personal injury. increase the risk of electric shock. BS305/BS340... - Page 4 Use power tools only with specifically operate the power tool. Power tools are designated battery packs. Use of any other dangerous in the hands of untrained users. battery packs may create a risk of injury or fire. BS305/BS340...
- Page 5 Damaged cables increase the risk of an or when inadvertently coming into contact with electric shock. the saw blade. b) Never remove cutting remainders, wood chips, etc. from the sawing area while the machine is running. BS305/BS340...
- Page 6 The smaller the gauge number of the wire the greater the capacity of the cord. e) When using a cable reel, always unwind the cable completely. BS305/BS340...
-
Page 7: Symbols & Cable Rating Chart
Caution! Wear a dust mask. Amperes 7.5M 0 – 2.0 2.1 – 3.4 3.5 - 5.0 5.1 – 7.1 7.1 – 12.0 12.1 – 20.0 BS305/BS340... -
Page 8: Machine Details And Product Features
MACHINE DETAILS AND PRODUCT FEATURES Machine Details Specifications: Specifications: BS305 BS340 Mains Voltage - 230V / 50Hz Power Consumption - 750W 1100W Blade Spec – 2240mm X 3-20mm 2560mm X 3-25mm Cutting Capacity - 165mm 225mm Throat Width - 305mm... - Page 9 MACHINE DETAILS AND PRODUCT FEATURES BS305/BS340 AIR6V AIR6V AIR6V AIR6V...
-
Page 10: Assembly
M6hex headed bolts and the 6mm flat washers. – Next fix the long and short horizontal braces but do not fully tighten them. – Stand the band saw up on to its stand and then tighten the nuts fully on the braces. BS305/BS340... -
Page 11: Assembly Instructions
Tool kit – Hang the push stick on the hook, and slide on the rip fence to the guide rail. Lower cover – Loosen the tracking lock knob. Tracking knob Push stick Rip fence Mitre gauge Tracking lock knob BS305/BS340... - Page 12 A. the blade indicator up or down as needed. Retighten the set screw. – Loosen knob B and adjust the thrust bearing so that it sits 0.5mm from the back of the blade, and then tighten knob B. BS305/BS340...
-
Page 13: Dust Extraction
–Loosen the socket head bolt E, and adjust trust bearing to a position of 0.5mm from rear of blade. Retighten the bolt E. – Loosen bolt F and adjust the guide bearing to a position 0.5mm away from blade. Retighten the bolt F. BS305/BS340... -
Page 14: Operation
– Move the fence to a needed position, the scale – Turn of machine and LED light. indicates distance form saw blade to the fence. – Tighten the lock lever to champ the rip fence. Lock lever BS305/BS340... - Page 15 –Place workpiece on the table. Warning:When cutting with mitre gauge, the –plug in. lock handle must be firmly tightened. –Start saw. –Cut workpiece in a single pass. –Switch off no further cutting is to be done immediately afterwards. BS305/BS340...
-
Page 16: Maintenance And Service
– Remove the blade and clean both top and bottom pulleys before installing the new blade. – Tighten the saw blade tension knob, and replace the guide rail and close the top and bottom covers. BS305/BS340... - Page 17 MAINTENANCE AND SERVICE – Now align and tension the blade then adjust the upper and lower blade guides as described earlier in this manual. Quick release lever BS305/BS340...
-
Page 18: Lumberjack Guarantee
If a return is requested by the Authorised Dealer or 1.2.3 If asked to do so by Lumberjack or its Lumberjack, you will be provided with a Returns Authorised dealer, you return the product at Material Authorisation number which must be your own cost to Lumberjack’s or supplying... - Page 19 Lumberjack. If you include a contact number with this it will speed your claim 2.4 Please note that it is essential that the letter of claim reaches Lumberjack on the last day of this Guarantee at the latest. Late claims will not be considered.
-
Page 20: Declaration Of Conformity
Is in compliance with the regulations included in the Directives:2006/95/EC EC DECLARATION OF CONFORMITY Certificate for EC-type examination delivered by TÜV Süd Product Service GmbH-80339 München GERMANY(Registration No.:N8M 15 04 28954 042 ) Person who declares: Bill Evans 01.03.2017 The Director BS305/BS340... -
Page 21: Parts List
Switch cover Guide plate Pan head screw Pulling plate LED switch Hex head bolt Serrated washer Flat washer Pan head screw Hex nut Thread forming screw bevel block Cord clamp Shaft Cord clamp Ball bearing Switch box BS305/BS340 AIR6V AIR6V AIR6V... - Page 22 Ball house Retaining ring Cover Bearing Interlock switch Shaft Switch Knob Hex nut Flat washer Set screw Socket head screw Flat washer Bushing Knob Guide block Shaft Shaft Handle Ball bearing Handle cap Socket head screw BS305/BS340 AIR6V AIR6V AIR6V...
- Page 23 Lock nut Socket head screw Pan head screw Flat washer Dust port cover Pointer Dust port Flat washer Pan head screw Hex head bolt Set screw Flat washer Bushing Socket head screw Idle pulley shaft Hex nut BS305/BS340 AIR6V AIR6V AIR6V...
- Page 24 Pan head screw Guide plate Open spanner Carriage blot 6mm hex wrench Fence 5mm hex wrench Socket head bolt 4mm hex wrench 3mm hex wrench Sliding base *Alternative parts. Your machine may not have this assembly part. BS305/BS340 AIR6V AIR6V AIR6V...
-
Page 25: Parts Diagram
Parts Diagram BS305/BS340... -
Page 26: Accessory For Circular Cutting(Option)
Remove old Connecting Block(NO.100) 1. Loosen the screw. 6. Tighten the socket head screw. 2. Pull the guide block . 7. Push the guide block the hole and tighten the screw. 3. Loosen the socket head screw. BS305/BS340... - Page 27 OPERATION Attention: To make a circular cutting, using a 4. You also can easily cut out round corner, sector with possible narrow saw blade is necessary. the accessory. 1.Draw a circle and its centre point on the wood workpiece. BS305/BS340...
Need help?
Do you have a question about the BS305 and is the answer not in the manual?
Questions and answers