Panasonic KX-MB2061CXB Service Manual page 124

KX-MB2061CXB/KX-MB2061CX2/KX-MB2062CXB
Code Function
591 FAX auto redial time disconnection
time set
592 CNG transmit select
593 Time between CED and 300bps
594 Overseas DIS detection select
595 Receive error limit value set
596 Transmit level set
598 Receiving sensitivity
599 ECM frame size
628 H.V.P.S. check
639 LSU test
655 Cause Distinction Code of Call Service 3
677 FAN test
710 Memory clear except History data
717 Transmit speed select
718 Receive speed select
722 Redial tone detect
731 CPC mode
763 CNG detect time for friendly reception 1:10 sec
774 Receiving T4 timer
775 Transmission T4 timer
784 Voice prompt test
815 Sensor check
852 Print test pattern
853 Top margin
854 Left margin
874 DTMF ON time
875 DTMF OFF time
880 History list
881 Journal 2 list
882 Journal 3 list
956 CORDLESS TEST MODE
Set Value Effective
Range
X second 001~999 185
1:OFF 1~3 2
2:ALL
3:AUTO
1:75 msec 1~3 1
2:500 msec
3:1 sec
1:detects at 1, 2 1
the 1st time
2:detects at
the 2nd time
1: 5% 1~4 2
2: 10%
3: 15%
4: 20%
X dBm - 15~00 10
43= -43 dBm 20~48 48
1:256 2:64 1, 2 1
1:14400BPS 1~6 1
2:12000BPS
3:9600BPS
4:7200BPS
5:4800BPS
6:2400BPS
1:14400BPS 1~6 1
2:12000BPS
3:9600BPS
4:7200BPS
5:4800BPS
6:2400BPS
1:ON 2:OFF 1, 2 1
X 10 msec 000~255 033
1~3 3
2:20 sec
3:30 sec
X 100 msec 00~99 00
X 100m sec 00~99 00
X 0.5mm 01~11
X 0.5mm 01~11
X msec 060~200 100
X 10 msec 06~20 10
Command
124
Default
Sets the FAX redial interval during FAX communi-
cation.
Lets you select the CNG output during FAX trans-
mission. ALL: CNG is output at phase A. AUTO:
CNG id output only when automatic dialing is per-
formed. OFF: CNG id not output at phase A. Refer
to Sometime There Is a Transmit Problem
(P.176).
See How To Output The Journal Report (P.183)
and Receive Problem (P.177).
See How To Output The Journal Report (P.183)
and Sometime There Is a Transmit Problem
(P.176).
If the number of errors during transmission exceeds
this value, the sending side terminates the call.
Selects the FAX transmission level. Refer to Some-
time There Is a Transmit Problem (P.176) and
Receive Problem (P.177).
Used when there is an error problem. Refer to How
To Output The Journal Report (P.183).
----------
See Test Functions (P.119).
See Test Functions (P.119).
See CALL SERVICE Troubleshooting Guide
(P.149).
See Test Functions (P.119).
Refer to Memory Clear Specification (P.125).
If the code 527 is set at 1, the code 717 and 718
work.
If the code 527 is set at 1, the code 717 and 718
work.
Sets the tone detection mode after redialing.
Sets the CPC signal detection mode from the con-
verter.
Selects the CNG detection tone of friendly recep-
tion.
Use this function when delay occurs in the line and
communication.
(ex. Mobile comm) does not work well.
Use this function when delay occurs in the line and
communication.
(ex. Mobile comm) does not work well.
You can hear the voice prompt from speaker after
pressing "SET" key.
See Test Functions (P.119).
See Test Functions (P.119).
05 ----------
06 ----------
----------
----------
See History (Example of a printed out list)
(P.131).
See Journal 2 (P.180).
See Journal 3 (P.181).
Remarks