Mitsubishi Electric M Series Manual page 23

[3] Use the F1 or F2 button to move
the cursor to select the mode
1. CONTROLS
number, and change the setting
number with the F3 or F4 button.
1-2. Wired Remote Controller [PAR-32MAA-J], cont.
PEAD-AA4, PEA, SEZ
• Make the above settings on Mr. Slim units as necessary.
Note:
Function
• Refer to the Instructions Book when it is necessary to set the settings for City Multi units.
• Table 1 summarizes the setting options for each mode number. Refer to the indoor unit Installation Manual for the
detailed information about initial settings, mode numbers, and setting numbers for the indoor units.
Heater OFF
• Be sure to write down the settings for all functions if any of the initial settings has been changed after the completion of
Inlet air temp. set temp
installation work.
Heater ON
Inlet air temp.< set temp - 4.5°F(2.5°C)
Table1. Function setting options
•The fan will stop and the heater will turn off when [DEFROST] or [ERROR] is displayed.
Mode No. Mode
01 Automatic recovery after power failure
02
Thermistor selection
Inlet air temp.
(indoor temperature detection)
03 LOSSNAY connection
Heater output
04 Power voltage
Heater
control Heater OFF
05 AUTO mode
Inlet air temp. set temp
Heater ON
07 Filter sign
Inlet air temp.< set temp - 4.5°F(2.5°C)
•The fan will drive and the heater will turn off when [DEFROST] is displayed.
08 Fan speed
Inlet air temp.
09 Outlet
10 Optional parts
Heater output
(High-efficiency filter)
11 Vane
(4) LOSSNAY setting (City Multi only)
This setting is required only when the operation of City Multi units is interlocked with LOSSNAY units. This setting is not available for the
Mr. Slim units. Interlock settings can be made for the indoor unit to which the remote controller is connected. (They can also be
confirmed or deleted.)
• Use the centralized controller to make the settings if it is connected.
Note:
• To interlock the operation of the indoor units with the LOSSNAY units, be sure to interlock the addresses of ALL indoor
units in the group and that of the LOSSNAY unit.
[Button operation]
[1] When "Lossnay" on the Service
menu is selected, the remote
controller will automatically begin
searching for the registered
LOSSNAY addresses of the
currently connected indoor unit.
To make LOSSNAY interlock setting
[3] Enter the addresses of the indoor unit and the LOSSNAY unit to be
interlocked, with the F1 through F4 buttons, select "Set" in the
"Function", and press the SELECT button to save the settings.
"Sending data" will appear on the screen. If the setting is
successfully completed, "Setting completed" will appear.
Due to continuing improvement, above specification may be subject to change without notice.
© 2016 Mitsubishi Electric US, Inc.
[4] When the settings are completed,
Function setting
Ref. address Unt # 1
Mode 7
Mode 8
Mode 9
Mode11
[5] When the transmission is
Request:
Cursor Cursor
Individual items
(Unit No. 1 through 4)
Setting
Settings
Disable
Set temp.
Enable (Four minutes of standby time is required after the restoration of power.)
(Room temperature setting)
Average temperature reading of the indoor units in operation
Thermistor on the indoor unit to which the remote controller is connected (fixed)
Set temp. -1.8°F (1°C)
Built-in sensor on the remote controller
Not connected
Set temp. -4.5°F (2.5°C)
Connected (without outdoor air intake by the indoor units )
ON
Connected (with outdoor air intake by the indoor units )
240 V
OFF
220 V, 230 V
Enable (Automatically the unit achieves effective energy saving operation.)
Disable
100 hours
2500 hours
Not displayed
Silent mode (or standard)
Standard (or High ceiling 1)
Set temp.
High ceiling (or High ceiling 2)
Set temp. -4.5°F (2.5°C)
4 directional
3 directional
2 directional
No
ON
Yes
OFF
No vanes (or the vane setting No.3 is effective.)
Equipped with vanes (The vane setting No.1 is effective.)
Equipped with vanes (The vane setting No.2 is effective.)
[2] When the search is completed,
Lossnay
IU address
Lossnay address
Collecting data
If no settings need to be made, press the RETURN button to go
back to the Service menu.
M-Series - Controls (December 2016)
press the SELECT button to send
the setting data from the remote
controller to the indoor units.
successfully completed, the screen
will return to the Function setting
screen.
Mode No.
( )RF thermostat
setup function No.
23
(123) (111)
Setting No.
1
1
2
1
2
3
1
2
3
1
2
1
2
1
2
3
1
2
2
3
1
2
3
1
2
1
2
3
the smallest address of the
indoor units that are connected
to the remote controller and the
address of the interlocked
LOSSNAY unit will appear. "--"
will appear if no LOSSNAY unit
is interlocked with the indoor
units.
Lossnay
IU address
Lossnay address
Sending data
Function setting
Ref. address Grp.
Sending data
Initial setting
(Factory setting)
11
Unit numbers
Set "Grp." for the Unit number.
●
-
These settings apply to all the connected
indoor units.
Set "1, 2, 3, 4, or All" for the Unit number.
These settings apply to each indoor unit.
• If "1, 2, 3, or 4" is set for the Unit number,
the settings apply only to the specified
indoor unit regardless of the number of
-
connected indoor units (one through four
units).
• If "ALL" is set for the Unit number, the
settings apply to all the connected indoor
units regardless of the number of
connected indoor units (one through four
units).
Lossnay
IU address
Lossnay address
Function Set/Conf/Del.
Select:
Cursor Address
Lossnay
IU address
Lossnay address
Setting completed
Return:
23