Panasonic AV-HS6000 Series Operation Manual page 57

f Set the size restriction on the amount of transition.
6
Set [Return Time] in the [Pattern Limit] column.
f Set the transition time to the position of the fader lever when [Pattern Limit] is set to [Off] from [On].
7
Set [X‑Pos] and [Y‑Pos] in the [Position] column.
f Set the start position of the next pattern waveforms.
- WIPE: 11, 12, 13, 14, 15
- SQ: 41, 42, 43, 44, 45, 51, 52, 53, 54
f These can be set only when the target pattern is selected in the background.
Either operate the fader lever or press the <AUTO> button to check the wipe operation.
Example) When [X-Pos] is set to [−50], and [Y-Pos] is set to [−50]
The next screen (or key) appears from the bottom left, and wipes in towards the center of the screen.
8
Set [Size] in the [Position] column.
f Set the start size of the next pattern waveforms.
- SQ: 51, 52, 53, 54
Setting trimming, aspect ratio
Set the behavior for the trimming and aspect ratio. This is applied to the background transition.
1
Select the <ME1>/<ME2> button → [BKGD] → [Position] tab.
2
Select an item in [Trim] in the [Trim] column.
f Set the trimming for the pattern waveforms of SQ, SL, and 3D.
[Off]
[16:9]
[4:3]*
1
[4:3 Smooth]*
1
[Manual]*
2
*1 Disabled when SD is selected as the system format.
*2 Enabled when the following pattern waveforms are selected.
SQ: 41, 51 - 54
3
Select an item in [Manual] in the [Trim] column.
[Free]
[Pair]
4
Select an item in [4:3 Auto] in the [Trim] column.
f Set the target sources for automatic trimming ([4:3] or [4:3 Smooth]). Enabled when HD is selected as the system format.
[Off]
[On]
5
Set [WipeAspect] in the [Trim] column.
f Adjust the aspect ratio of the wipe pattern.
f The following pattern waveforms are changed.
- WIPE: 11 - 15
- SQ: 42 - 45
f SQ41 and 51 to 54 are not applicable. The aspect ratio is adjusted with [Trim], [Trim Adjust1], or [Trim Adjust2].
6
Select an item in [Smooth] in the [Trim] column.
[OFF]
[ON]
f Modifies the next pattern waveforms.
- WIPE: 11 - 15
- SQ: 42 - 45
f SQ41 and 51 to 54 are also applicable. [Trim Adjust1] and [Trim Adjust2] will change to the standard ratio when [Trim] is set to [Manual].
Setting the 3D (turn page) effect
A lighting effect can be added to a wipe pattern. Alternatively, the parameters for turn page effect can be set.
f These effects can be set for background transitions and key transitions.
Chapter 5 Basic Operations — Wipe
Does not perform trimming.
Trims the edges around a source at a certain amount. This setting is used when a black border is seen around the
source.
The edges are trimmed at a certain amount when SD is selected as the system format.
Performs trimming in the 4:3 aspect ratio and releases the trimming when the transition is completed.
Performs trimming in the 4:3 aspect ratio, and smoothly executes transition to the 16:9 video.
Trims the waveform using the values set in [Trim Adjust1] and [Trim Adjust2].
Sets the amount of trimming for [Left], [Right], [Top], and [Bottom] separately.
Changes the settings in such a way that the [Left] and [Right] trimming amounts, and the [Top] and [Bottom] trimming
amounts are the same. (This makes for a top-bottom and left-right symmetry.)
All input sources are targeted for automatic trimming.
The input sources for which [Edge Crop] is selected in the up-converter setting are targeted for automatic trimming. Input
sources for which an item other than [Edge Crop] is selected are trimmed in [16:9].
The aspect ratio for set wipe pattern will be constant regardless of the transition.
For SQ waveform, it may become discontinuous at the edge of transition.
The aspect ratio is changed from the aspect ratio of the preset wipe pattern to the standard ratio in accordance with the
transition.
– 57 –