Advertisement
Quick Links
Road Lights with Brake Lights Kit
Groundsmaster
Model No. 02917—Serial No. 312000001 and Up
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
8
© 2012—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
3400-D Traction Unit
Description
No parts required
Rear light bracket, L.H.
Rear light bracket, R.H.
Bolt, M16 x 110mm
Nut, M16
Fuse, 15 amp
Dowty seal, 1/4 inch
Pressure switch adapter
Pressure switch
Pressure switch cable
Number plate bracket
PM2 Connector Gothic
Flasher relay
Standard shorter relay
Center headlight mount
R.H. Headlight mount
L.H. Headlight mount
Screw, M6 x 20mm
Nut, nyloc M6
Screw, M10 x 25mm
Nut, nyloc M10
Washer, 3/8 inch
Mounting bracket
PM4 Connector
Instrument panel connector lead
Switch, hazard warning
Switch, lights
Switch, indicator
Button, horn
Decal, horn
Cable tie
Cable tie
Reflector
Serial label
Register at www.Toro.com.
Form No. 3373-375 Rev A
Installation Instructions
Qty.
–
Initial preparation
1
1
2
Install the rear lights
2
2
1
1
Install the pressure switch
1
1
1
1
Install the number plate bracket
1
1
1
1
1
8
8
Install the front lights
4
4
8
2
2
1
1
1
1
Install the control panel switches
1
1
10
14
2
Install the reflectors
1
Install the serial label
Use
Original Instructions (EN)
Printed in the UK.
All Rights Reserved
Advertisement
Related Manuals for Toro 02917
Summary of Contents for Toro 02917
- Page 1 Form No. 3373-375 Rev A Road Lights with Brake Lights Kit Groundsmaster ® 3400-D Traction Unit Model No. 02917—Serial No. 312000001 and Up Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped.
-
Page 2: Initial Preparation
Media and Additional Parts Description Qty. Installation Instructions Read before installing and operating kit Parts Catalog Use to reference part numbers Initial Preparation No Parts Required Procedure 1. Park the machine on a level surface, lower the cutting unit, stop the engine, engage the parking brake and remove the key from the ignition switch. - Page 3 Note: If there is already a beacon kit fitted to the right side or a waste bin kit fitted to left side, it is allowable to use the same bolt for the installation. It is advisable to use the new M16 nyloc nuts provided with this kit.
-
Page 4: Installing The Pressure Switch
g018247 Figure 6 1. Dowty seal, 1/4 inch 3. Pressure switch 2. Pressure switch adapter 4. Screw the pressure switch into this adapter (Figure 6). Torque the switch to 34 N-m (25 ft-lbs). 5. Working on the electrical bulkhead, plug the 3-pin connector of the electrical pressure switch cable to g018244 the corresponding connector located on the main... - Page 5 Installing the Number Plate Bracket Parts needed for this procedure: Number plate bracket PM2 Connector Gothic g018277 Figure 9 Flasher relay Standard shorter relay 1. Red wire 3. PM2 connector 2. Black wire Procedure 4. Connect the number plate light wiring to either The number plate with light attaches to the bulkhead.
- Page 6 Installing the Front Lights Parts needed for this procedure: Center headlight mount R.H. Headlight mount L.H. Headlight mount Screw, M6 x 20mm Nut, nyloc M6 Screw, M10 x 25mm Nut, nyloc M10 Washer, 3/8 inch g018249 Mounting bracket Figure 11 PM4 Connector 1.
- Page 7 g018251 Figure 13 1. Blue 4. Black 2. Green/White 5. Green 3. Red/White 6. PM4 connector g018250 13. Secure the connector, on the machine wiring loom Figure 12 with the GREEN/RED wire, to the identified R/H 1. Blue 4. Black light assembly connector (Figure 14).
- Page 8 Installing the Control Panel Switches Parts needed for this procedure: Instrument panel connector lead Switch, hazard warning Switch, lights Switch, indicator Button, horn g018292 Decal, horn Figure 15 Cable tie 1. Switch blank–light switch 2. Switch blank–hazard Cable tie switch 7.
- Page 9 G018336 Figure 17 G018338 1. Round blanking plug–horn 2. Rectangular blanking Figure 19 button plug-indicator switch 1. Green/Red 2. Green/White 9. Install the horn decal lining up the edges of the 11. Connect the direction indicator switch to the round and rectangular holes (Figure 18). connector lead instrument panel.
- Page 10 Installing the Reflectors Parts needed for this procedure: Reflector Procedure Affix a reflector to each side of the engine cover. Ensure that the outside edge of each reflector is adhered 100mm (4 inches) from each edge of the engine cover (Figure 20).
-
Page 11: Operation
Using the top screws shown in Figure 21, adjust the Important: Replace all worn or damaged parts headlights per local standards. with genuine Toro parts. 1. Check that all lights are working on a regular basis. 2. Ensure the headlights are adjusted correctly. - Page 12 Countries Other than the United States or Canada Customers should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company.