Cleaning & Maintenance; Cleaning The Filter; Pressure Test Adaptor Fitting Instructions - Aqualisa QUARTZ Electric Installation Manual

Cleaning & maintenance
Cleaning & maintenance
Your Quartz Electric unit should be cleaned using only a soft cloth and washing up liquid.
Your Quartz Electric unit should be cleaned using only a soft cloth and washing up liquid.
DO NOT USE ABRASIVE CLEANERS.
DO NOT USE ABRASIVE CLEANERS.
To reduce the requirement for chemical descaling in hard water areas, the shower head incorporates rub clean
To reduce the requirement for chemical descaling in hard water areas, the shower head incorporates rub clean
teats. Any scale build up that may occur in any of the holes can be broken down by gently rubbing the flexible
teats. Any scale build up that may occur in any of the holes can be broken down by gently rubbing the flexible
tips of the jets during use. This procedure should be completed regularly, as often as once a week in some hard
tips of the jets during use. This procedure should be completed regularly, as often as once a week in some hard
water areas as scale build up can affect the spray pattern and cause the shower to perform poorly.
water areas as scale build up can affect the spray pattern and cause the shower to perform poorly.
Should chemical descaling of the head become necessary, remove the shower head and fully immerse in a mild
Should chemical descaling of the head become necessary, remove the shower head and fully immerse in a mild
proprietary descalent.
proprietary descalent.
! IT IS IMPERATIVE THAT DESCALING IS CARRIED OUT STRICTLY IN ACCORDANCE WITH THE
! IT IS IMPERATIVE THAT DESCALING IS CARRIED OUT STRICTLY IN ACCORDANCE WITH THE
MANUFACTURERS INSTRUCTIONS. SUBSTANCES THAT ARE NOT SUITABLE FOR PLASTICS AND
MANUFACTURERS INSTRUCTIONS. SUBSTANCES THAT ARE NOT SUITABLE FOR PLASTICS AND
ELECTROPLATED SURFACES MUST NOT BE USED.
ELECTROPLATED SURFACES MUST NOT BE USED.

Cleaning the filter

Cleaning the filter
Cleaning the filter should only be completed by a qualified person.
Cleaning the filter should only be completed by a qualified person.
1. Turn the shower electrical isolating switch off.
1. Turn the shower electrical isolating switch off.
2. Isolate the water supply to the shower.
2. Isolate the water supply to the shower.
3. Carefully remove fixing screws from the top and bottom of the front cover.
3. Carefully remove fixing screws from the top and bottom of the front cover.
Carefully pull the front cover away from the unit ensuring the solenoid
Carefully pull the front cover away from the unit ensuring the solenoid
connector block is detached.
connector block is detached.
4. Unscrew the two screws on the filter protective cover and remove the
4. Unscrew the two screws on the filter protective cover and remove the
filter assembly. (Fig.2).
filter assembly. (Fig.2).
5. Remove the filter assembly and clean as necessary. (Fig.3).
5. Remove the filter assembly and clean as necessary. (Fig.3).
6. Refit the filter assembly and protective cover. Reassemble the unit in reverse of the above procedure.
6. Refit the filter assembly and protective cover. Reassemble the unit in reverse of the above procedure.

Pressure test adaptor fitting instructions

Pressure test adaptor fitting instructions
Quartz Electric requires the following dynamic (running) water pressure:
Quartz Electric requires the following dynamic (running) water pressure:
Maximum: 1.0MPa (10bar)
Maximum: 1.0MPa (10bar)
Minimum: 0.09MPa (0.9bar) at a flow rate of 8lpm
Minimum: 0.09MPa (0.9bar) at a flow rate of 8lpm
To ensure the water pressure to the shower is adequate, we recommend adopting the following procedure:
To ensure the water pressure to the shower is adequate, we recommend adopting the following procedure:
1. Isolate the electrical supply to the shower.
1. Isolate the electrical supply to the shower.
2. Isolate the water supply to the shower.
2. Isolate the water supply to the shower.
3. Remove the fixing screws from the top and bottom of the front cover. Carefully detach the solenoid
3. Remove the fixing screws from the top and bottom of the front cover. Carefully detach the solenoid
connector and pull the front cover clear.
connector and pull the front cover clear.
4. Remove the pressure test adaptor from the inside of the front cover.
4. Remove the pressure test adaptor from the inside of the front cover.
5. Unscrew the two fixing screws on the filter and remove the filter assembly.
5. Unscrew the two fixing screws on the filter and remove the filter assembly.
Fig.2
Fig.3
Quartz Electric Installation Guide 08
TM
Fig.2
Fig.3
Qu