During Operation; During Operation Safety - Toro Z Master 8000 Series Operator's Manual

N position. Try starting the engine; the
EUTRAL
engine should not start.
3. Sit on the seat, disengage the parking brake,
move the PTO-engagement lever to the O
position, and move the speed-control lever to
the N position. Try starting the engine;
EUTRAL
the engine should not start.
4. Sit on the seat, engage the parking brake,
move the PTO-engagement lever to the O
position, and move the speed-control lever to the
N position. Now start the engine. While
EUTRAL
the engine is running, release the parking brake,
engage the PTO-engagement lever, and rise
slightly from the seat; the engine should shut off.
5. Sit on the seat, engage the parking brake,
move the PTO-engagement lever to the O
position, and move the speed-control lever to
the N position. Now start the engine.
EUTRAL
Move the speed-control lever forward; the
engine should shut off.

During Operation

During Operation Safety

General Safety
•
The owner/operator can prevent and is responsible
for accidents that may cause personal injury or
property damage.
•
Wear appropriate clothing, including eye
protection; slip-resistant, substantial footwear; and
hearing protection. Tie back long hair and do not
wear jewelry.
•
Do not operate the machine while ill, tired, or
under the influence of alcohol or drugs.
•
Never carry passengers on the machine and keep
bystanders and pets away from the machine
during operation.
•
Operate the machine only in good visibility to avoid
holes or hidden hazards.
•
Avoid mowing on wet grass. Reduced traction
could cause the machine to slide.
•
Ensure that all drives are in neutral, the parking
brake is engaged, and you are in the operating
position before you start the engine.
•
Keep your hands and feet away from the cutting
units. Keep clear of the discharge opening at all
times.
•
Look behind and down before backing up to be
sure of a clear path.
•
Use care when approaching blind corners, shrubs,
trees, or other objects that may obscure your
vision.
•
Do not mow near drop-offs, ditches, or
embankments. The machine could suddenly roll
over if a wheel goes over the edge or if the edge
gives way.
FF
•
Stop the blades whenever you are not mowing.
•
Stop the machine and inspect the blades after
striking an object or if there is an abnormal
vibration in the machine. Make all necessary
repairs before resuming operation.
FF
•
Slow down and use caution when making turns
and crossing roads and sidewalks with the
machine. Always yield the right-of-way.
•
Disengage the drive to the cutting unit and shut
off the engine before adjusting the height of
cut (unless you can adjust it from the operating
FF
position).
•
Never run an engine in an area where exhaust
gases are enclosed.
•
Never leave a running machine unattended.
•
Before leaving the operating position (including
to empty the catchers or to unclog the chute), do
the following:
– Stop the machine on level ground.
– Disengage the power take-off and lower the
attachments.
– Engage the parking brake.
– Shut off the engine and remove the key.
– Wait for all moving parts to stop.
•
Do not operate the machine when there is the risk
of lightning.
•
Do not use the machine as a towing vehicle.
•
Do not change the governor speed or overspeed
the engine.
•
Use accessories and attachments approved by
Toro only.
Slope Safety
•
Slow down the machine and use extra care on
hillsides. Travel up and down on hillsides. Turf
conditions can affect the stability of the machine.
•
Avoid turning the machine on slopes. If you must
turn the machine, turn it slowly and gradually
downhill, if possible.
•
Do not turn the machine sharply. Use care when
reversing the machine.
•
Use extra care while operating the machine with
attachments; they can affect the stability of the
machine.
•
A 2-post ROPS (Rollover Protection System) is
available for the machine as an accessory. A
ROPS is recommended if you will be mowing next
20