Head - Sanyo DVP-P1EX Technical Information

3-3.

HEAD

(See Figs. 3-3-1 to 3-3-3)
3-3-1. "COMPL, HOUSING REEL T (2E000) ",
"CORD, TERMINAL (2J000) ", "ASSY,
LEVER, TPH DOWN (1F000) ", and
"COMPL PWB, MC-1 (MC-1) "
1) Referring to section 3-1, remove the "MOTOR, FAN DC
(7M000)
1.8W ".
2) Remove the "SCR S-TPG BIN 2.6X4
remove the "CORD, TERMINAL
3-3-1.)
3) Remove the "COMPL, HOUSING REEL T
(Refer to Fig. 3-3-1.)
4) Remove the "SPECIAL WAHSER-3X0.5
fer to Fig. 3-3-1.)
5) Remove dowel 1 on the "ASSY, LEVER,TPH DOWN
(1F000)
" from hole 1 on the "ASSY, CHASSIS R
(Refer to Fig. 3-3-2.)
NOTE: When carrying out steps 5) - 8), be careful not to
injure the surface of the head by pressing down too hard
on the "COMPL,HOLDER TPH
2-2. To prevent injury to the surface of the head, insert
printing paper (approx. 100mm wide x 148mm long) from
the ink ribbon slot.
6) Insert dowel 1 side of portion A on the "ASSY, LEVER,
(1F000)
TPH DOWN " into hole 2 on the "ASSY, CHASSIS
R (7A000) " as shown in Fig. B of Fig. 3-3-2.
7) While press the "ASSY, LEVER, TPH DOWN
approximately 2mm to the "ASSY, CHASSIS R
(7A000)
" side, pull hole 3 on the "ASSY, LEVER, TPH
(1F000)
DOWN " out from shaft 2 on the "ASSY, CHAS-
(7C000)
SIS L ". (Refer to Fig. 3-3-2.)
8) Be careful not to distort the "ASSY, CHASSIS R" and pull
portion A out from hole 2 and remove the "ASSY, LEVER,
(1F000)
TPH DOWN ". (Refer to Fig. 3-3-2.)
9) Disconnect the connector from the "COMPL PWB, MC-1
(MC-1)
".
10) Remove the "SCR S-TPG BIN 2.6X4
remove the "COMPL PWB, MC-1
3-3-2.)
NOTE: It is unnecessary to remove the "COMPL PWB,
(MC-1)
MC-1 " to replace the "COMPL, HOLDER TPH
(1A000)
".
ASSEMBLY NOTES:
1. Insert portion B on the "COMPL, HOUSING REEL T
(2E000)
" into hole on the "ASSY, CHASSIS R
as shown in Fig. A of Fig. 3-3-1.
2. Align hole 3 with shaft 2 on the "ASSY, CHASSIS L
(7C000)
". Align dowel 1 with hole 1 on the "ASSY,
(7A000)
CHASSIS R
"SLIDE, LEVER TPH
shaft 1 are on the "ASSY, LEVER, TPH DOWN
Be careful not to distort the "ASSY, CHASSIS R/L" and
install the "ASSY, LEVER, TPH DOWN
(2F000)
(2J000)
". (Refer to Fig.
(2E000)
(1G000)
(7A000)
(1A000)
" shown in Fig. 3-
(1F000)
(7K000)
(MC-1)
". (Refer to Fig.
(7A000)
". Align shaft 1 with slot 1 on the
(5M000)
". (Hole 3, dowel 1, and
(1F000)
(1F000)
".
ASSY, CHASSIS R (7A000)
" and
Hole
".
". (Re-
Fig. A
".
ASSY,LEVER,TPH DOWN
(1F000)
"
" and Shaft 2
"
Ink ribbon
slot
").
ASSY,CHASSIS L
(7C000)
SCR S-TPG BIN 2.6X4 (7K000)
–10–
SPECIAL
WAHSER-3X0.5
(1G000)
COMPL,HOUSING
REEL T (2E000)
Portion B
SSCR S-TPG BIN
2.6X4 (2F000)
CORD,TERMINAL
(2J000)
Fig. 3-3-1
Portion A
Shaft 1
Dowel 2
Dowel 1
Hole 3
While turning the
"ASSY, LEVER, TPH
SLIDE,LEVER
DOWN (1F000) ", insert
TPH (5M000)
its dowel 1 side slightly
into hole 2.
ASSY,CHASSIS R
(7A000)
COMPL,HOLDER
TPH (1A000)
COMPL PWB,MC-1 (MC-1)
Connector
Fig. 3-3-2
Fig. B
Hole 2
Slot 1
Hole 2
Hole 1