Table of Contents
Advertisement
CONTENTS
1
INTRODUCTION ......................................................... 1
2
SETTING UP ............................................................... 2
2.1
Instrument Power-up ........................................ 2
2.1.1
Power-up Error Codes ........................ 3
2.2
Fitting the Chart ................................................ 4
2.3
Fitting the Pen Capsule(s) ............................... 4
3
DISPLAYS & CONTROLS .......................................... 5
3.1
Displays and L.E.D. Indicators ......................... 5
3.2
Use of Controls ................................................ 7
4
GENERAL OPERATION ............................................. 8
4.1
Input Error Messages ....................................... 9
5
CONTROL OPERATION ........................................... 10
5.1
Operating Page Introduction .......................... 12
5.1.1
Set Point Tracking ............................ 12
5.1.2
Auto/Manual Transfer ....................... 12
5.1.3
Profile Control ................................... 12
5.1.4
Cascade Control ............................... 12
5.1.5
Heat/Cool Control ............................. 12
5.2
Operating Page Displays ............................... 13
5.3
Alarm Acknowledge Page .............................. 16
5.3.1
Alarm Indications .............................. 16
5.3.2
Acknowledging Alarms ..................... 16
5.3.3
Using the Alarm Acknowledge Page 16
5.4
Totals Page Displays ...................................... 17
5.5
Access to Configuration Levels ..................... 18
5.5.1
Security Code Page .......................... 18
5.6
Profile States Page ........................................ 19
5.7
Auto-tuning Introduction ................................. 20
5.7.1
Auto-tuning Page .............................. 21
5.8
Auto-tuning Diagnostic Messages ................. 24
5.9
Introduction to Standard Control .................... 25
5.9.1
Control Page (Standard Control) ...... 30
5.10
Introduction to Heat/Cool Control .................. 31
5.10.2 Calculating the Crossover Value ...... 33
5.10.3 Calculating the Transition
Bandwidth Value ............................... 33
6
RECORD OPERATION ............................................. 34
6.1
Operating Page Displays ............................... 35
6.2
Alarm Acknowledge Page .............................. 36
6.2.1
Alarm Indications .............................. 36
6.2.2
Acknowledging Alarms ..................... 36
6.2.3
Using the Alarm Acknowledge Page 36
6.3
Totals Page Displays ...................................... 37
7
SIMPLE FAULT FINDING ......................................... 38
8
SPARES LIST ........................................................... 39
1 INTRODUCTION
Page
The COMMANDER 1900 series of documentation is shown in
Fig. 1.1. The
Standard Manuals
sheet, are supplied with all instruments. The
supplied depend on the specification of the
Manuals
instrument.
INSTALLATION
Product Identification
Siting
Mounting
Electrical Connections
Installation Record
IM/C1900-INS
PROGRAMMING
Basic Config. Level
Control Config. Level
Advanced Config. Level
IM/C1900-PGC
ADVANCED SOFTWARE
OPTIONS
Flow Totalisation
Ramp/Soak Profile
Maths Functions
Timer Functions
IM/C1900-ADV
B - Supplementary Manuals
Fig. 1.1 COMMANDER 1900 Documentation
, including the specification
OPERATION
Setting Up
Error Messages
Displays & Controls
Operating Level
Simple Fault Finding
Part No.
IM/C1900-OGC
SPECIFICATION SHT.
Full Specification
Part No.
SS C1900
A - Standard Manuals
Modbus (RTU)
Serial Adaptors
Serial Connections
Programming Pages
ASCII Tables
Part No.
IM/C1900-MOD
Supplementary
Part No.
Part No.
Part No.
1
- Quick Links:
- Input Error Messages
- Simple Fault Finding
Hide quick links:
Advertisement
Table of Contents
