Canon iPF6100 Service Manual page 142

Chapter 1
[Set./Adj. Menu]
[Test Print] [Nozzle Check]
[Status Print]
[Interface Print]
[Paper Details]
[Print Job Log]
[Menu Map]
[Adjust [Head Posi.
Printer] Adj.]
[Feed Priority] [Adj. Priority] [Automatic]
[Adj. Fine Feed]
[Adj Far Ed Feed]
[Calibration]
[Maintenance] [Head Cleaning]
[Nozzle Check]
[Replace P.head]
[Repl. maint cart]
[Head Info]
[Clean Platen]
1-124
Setting Item
[Auto(Standard)]
[Auto(Advanced)]
[Auto(Expansion)]
[Manual]
[Print Quality]
[Print Length]
[Adj. Quality] [Auto(Genuine
Ppr)]
[Auto(OtherPa
per)]
[Manual]
[Adjust [AdjustmentPr
Length] int]-[A:High]/
[B:Standard/
Draft]
[Change
Settings]-
[A:High]/
[B:Standard/
Draft]
[Auto Adjust]
[Calibration Log]
[Use Adj. Value]
[Return Defaults]
T-1-85
Description/Instructions
Print a nozzle check pattern.
Print the printer information.
Print the interface settings.
Prints the paper settings set with [Paper Details].
Print print job information such as paper type, size, and ink consumption. Ink consumption is
the approximate amount of ink used to print one sheet.
Print the menu list.
The printer prints and reads a test pattern for automatic adjustment of Printhead alignment
relative to the printing direction.
The printer prints and reads a test pattern for automatic adjustment of Printhead alignment
relative to the printing direction and spacing between nozzles and colors.
Try adjustment in this mode if "Auto(Standard)" does not improve printing.
The printer prints and reads a test pattern for automatic adjustment of Printhead alignment
relative to the printing direction and spacing between nozzles and colors. Adjustment is
performed at a higher level of precision than Auto(Advanced).
Try adjustment in this mode if vertical lines are warped or colors are out of alignment when the
printer driver option "High-Precision Printing" or "Priority on dot placement accuracy" is
selected.
Print a test pattern for adjustment of Printhead alignment relative to the printing direction. Enter
the adjustment value manually based on the resulting pattern.
Set the priority feed precision. Normally select [Automatic]. Select [Print Quality] to print at
high quality. Select [Print Quality] to reduce horizontal streaks. Select [Print Length] to
accurately control the feed amount. However, selecting [Print Length] may cause colors to
become slightly uneven in the carriage scan direction.
Set when using paper described in the paper reference guide.
A pattern to adjust the paper feed amount is printed, and the feed amount is automatically
adjusted from the printed result.
Set when using paper not described in the paper reference guide.
A pattern to adjust the paper feed amount is printed, and the feed amount is automatically
adjusted from the printed result.
This takes longer than [Auto (GenuinePpr)] to print and consumes more ink.
Select for paper that cannot be adjusted by [Auto(GenuinePpr)] or [Auto(OtherPaper)], such as
highly transparent paper.
Print a pattern to adjust the paper feed amount according to the type of paper.
Print a test pattern for adjustment relative to paper stretching or shrinkage, after which you can
enter the amount of adjustment.
Displayed when [Print Length] is selected as [Adj. Priority] for [Feed Priority].
Adjust the expansion rate of the currently loaded paper.
Enter the result adjusted with [AdjustmentPrint] or the difference with your own measurement
in %.
Increase the adjustment value to increase the feed amount for paper that tends to expand, and
reduce it for paper that tends to shrink.
Displayed when you have selected Feed Priority >Adj. Priority >Automatic or Print Quality.
Fine-tune the feed amount manually during printing.
Choose Yes to adjust the feed amount for the trailing edge.
Choose Yes for automatic adjustment of the adjustment value after a test pattern for color
calibration is printed. The new color calibration adjustment value is applied in all print jobs.
Check the date when color calibration was executed, as well as the type of paper used, as shown
on the Display Screen.
Choose Disabled >OK if you prefer not to apply the color calibration adjustment value in print
jobs. The printer driver settings will be used instead.
Choose Enabled >OK to apply the color calibration adjustment value in print jobs. However,
printer driver settings are given priority.
Clear the color calibration adjustment value and the execution log.
Specify Printhead cleaning options.
Choose Head Cleaning A if printing is faint, oddly colored, or contains foreign substances.
Choose Head Cleaning B if no ink is printed at all, or if printing is not improved by Head
Cleaning A.
Print a nozzle check pattern.
Not displayed during a warning message that the remaining Maintenance Cartridge capacity is
low.
When replacing the Printhead, choose Yes and follow the instructions on the screen.
When exchanging the maintenance cartridge, choose Yes and follow the instructions on the
screen.
Indicates information about the printhead.
Move the Carriage in preparation for cleaning the Platen.